孔用弹性挡圈-a型_(摘自gb_893.1-86).docxVIP

孔用弹性挡圈 -A 型 （摘自 GB 893.1-86 ） 孔径的 d0 =8～200mm的 A 型孔用弹性挡圈。 标记示例 : 孔径 d0=50、材料 65Mn、热处理硬度 HRC44～ 51、经表面氧化处理的 A 型孔用弹性挡圈的标记： 挡圈 GB 893.1 50 孔径的 d0 =20～ 200mmA型孔用弹性挡圈： 挡 圈 沟 槽（推荐） 孔径 轴 D S d m d3 d0 2 n d1 ≤ ≥ 基本尺寸 极限偏差 基本尺寸 极限偏差 基本尺寸 极限偏差 基本尺寸 极限偏差 8 8.7 +0.36 0.6 +0.04 1 8.4 +0.09 0.7 +0.14 2 -0.10 -0.07 0 0.6 0 9 9.8 +0.36 0.6 +0.04 1 9.4 +0.09 0.7 +0.14 2 -0.10 -0.07 0 0.6 0 10 10.8 +0.36 0.8 +0.04 1.5 10.4 +0.11 0.9 +0.14 2 -0.10 -0.10 0 0.6 0 11 11.8 +0.36 0.8 +0.04 1.5 11.4 +0.11 0.9 +0.14 3 -0.10 -0.10 0 0.6 0 12 13 +0.36 1 +0.04 1.5 12.5 +0.11 0.9 +0.14 4 -0.10 -0.10 0 0.9 0 13 14.1 +0.36 1 +0.04 1.7 13.6 +0.11 0.9 +0.14 4 -0.10 -0.10 0 0.9 0 14 15.1 +0.36 1 +0.05 1.7 14.6 +0.11 1.1 +0.14 5 -0.10 -0.13 0 0.9 0 15 16.2 +0.36 1 +0.05 1.7 15.7 +0.11 1.1 +0.14 6 -0.10 -0.13 0 1.2 0 16 17.3 +0.36 1 +0.05 1.7 16.8 +0.11 1.1 +0.14 7 -0.10 -0.13 0 1.2 0 17 18.3 +0.42 1 +0.05 1.7 17.8 +0.11 1.1 +0.14 1.2 8 -0.13 -0.13 0 0 18 19.5 +0.42 1 +0.05 1.7 19 +0.13 1.1 +0.14 1.5 9 -0.13 -0.13 0 0 19 20.5 +0.42 1 +0.05 2 20 +0.13 1.1 +0.14 1.5 10 -0.13 -0.13 0 0 20 21.5 +0.42 1 +0.05 2 21 +0.13 1.1 +0.14 1.5 10 -0.13 -0.13 0 0 21 22.5 +0.42 1.2 +0.05 2 22 +0.13 1.1 +0.14 1.5 11 -0.13 -0.13 0 0 22 23.5 +0.42 1.2 +0.05 2 23 +0.13 1.1 +0.14 1.5 12 -0.13 -0.13 0 0 24 25.9 +0.42 1.2 +0.05 2 25.2 +0.21 1.3 +0.14 1.8 13 -0.21 -0.13 0 0 25 26.9 +0.42 1.2 +0.05 2 26.2 +0.21 1.3 +0.14 1.8 14 -0.21 -0.13 0 0 26 27.9 +0.42 1.2 +0.05 2 27.2 +0.21 1.3 +0.14 1.8 15 -0.21 -0.13 0 0 28 30.1 +0.50 1.2 +0.05 2 29.4 +0.21 1.3 +0.14 2.1 17 -0.25 -0.13 0 0 30 32.1 +0.50 1.2 +0.05 2 31.4 +0.25 1.3 +0.14 2.1 18 -0.25 -0.13 0 0 31 33.4 +0.50 1.5 +0.05 2.5 32.7 +0.25 1.3 +0.14 2.6 19 -0.25 -0.13 0 0 32 34.4 +0.50 1.5 +0.05 2.5 33.7 +0.25 1.3 +0.14 2.6 20 -0.25 -0.13 0 0 34 36.5 +0.50 1.5 +0.06 2.5 35.7 +0.25 1.7 +0.14 2.6 22 -0.25 -0.15 0 0 35 37.8 +0.50 1.5 +0.06 2.5 37 +0.25 1.7 +0.14 3 23 -0.25 -0.15 0 0 36 38.8 +0.50 1.5 +0.06 2.5 38 +0.25 1.7 +0.14 3 24 -0.25 -0.15 0 0 37 39.8 +0.50 1.5 +0.06 2.5