PCB缺陷英语汇总.docVIP

开路 open circuit 2短路 short circuit 线路狗牙 circuit wist 3线路缺口 circuit nick 4线路凹痕 circuit dent 5渗镀 plating Bloody 6焊盘缺口 pad nick 7内层白斑 I/L white spot 8黑化不良 poor B.O 9爆板 measling 10粉红圈 pinking ring 11层压起泡 press blister 12错位 misregistation 13偏位 shift 14孔内无铜 no Cu on Pth 15孔内毛刺 hole burrs 16NPTH有铜 Cu on NPTH 17铜面露基材 exposed laminate 18铜面凹痕 dent on Cu surface 19胶渍 gum residue 20夹膜 D/F nip 21蚀刻不尽 under etching 22线幼 line too thin 23孔大 hole oversize 24孔小 hole undersize 25偏孔 hole misregistration 26铜面瘤粒 Cu nodule 27显影不尽 under developing 28铜面刮伤 scratch on Cu surface 29塞孔 hole plugged 30修理不良 poor repairing 31铜薄 copper too thin 32内层擦花 I/L scratch 33内层偏位 I/L misregistation 34内层杂物 I/L inclusions 35掉膜 film off 36干膜碎 D/F meaking 37退锡不尽 poor Sn stripping 38间隙小 space too marrow 39板薄 board too thin 40板厚 board too thickness 41针孔 pinhole 42崩孔 breakout 43侧蚀 undrcut 44镀层粗糙 plating layer roughness 45亚色 dull colour 46焊 盘 翘 起 lifted land 47漏 钻 孔 missing hole 48露 布 纹 weave exposure 49钻 偏 孔 hole misregistratiion 50孔 损 害 hole damage 51基 材 分 层 delamination 52蚀 刻 过 度 over etching 53多 孔 hole too much 54残 铜 remain Cu 55孔 内 露 基 材 laminate exposure in hole 56焊 盘 脱 落 pad break off 57焊 盘 凹 痕 pad dent 58焊 盘 凸 起 pad bulge 59焊 盘 损 坏 pad damaged 60焊 盘 缺 口 pad nick 61焊 盘 露 铜 pad expose Cu 1板面凹痕 dent 2内层白斑 I/L white spot 3线路缺口 circuit nick 4蚀刻不净 undering etching 5绿油剥离 S/M peel off 6显影不净 under developing 7基 材 白 点 laminate measling 8铜面氧化 copper oxide 9绿油上焊盘 s/m on pad 10白字上焊盘 c/m on pad 11阻焊不良 poor S/M 12线路擦花 track scratch 13锡上线 sn on circuit 14聚锡 sn mass 15锡灰 sn gray 16焊盘露铜 cu exposed on pad 17锡上金手指 sn on G/F 18金手指凹痕 G/F dent 19金手指擦花 G/F scratch 20金手指粗糙 G/F roughness 21v-cut不良 poor V-cut 22倒边不良 poor milling 23针床压伤 ET dent 24拖锡不良 poor touch up 25补金不良 poor repairing Au 26补油不良 poor repairing s/m 27针孔 pinhole 28胶渍 paster stain 29k孔内毛刺 burrs in hole 30锡珠入孔 solder in hole 31露铜 expose Cu 32露镍 expose Ni 33绿油起泡 solder mask blister 34绿油起皱 solder mask winbles 35金手指氧化 G/F oxiding 36金颜色不良 Au discoloration