关节轴承公差表.docxVIP

关节轴承公差表 尺寸和公差符号 The symbols of dimension and tolerance d: 轴承公称内径。 Bearing bore diameter, nominal. dmp: 单一平面平均内径偏差。 Single plane mean bore diameter deviation. Vdp: 单一径向平面内径变动量。 Bore diameter variation in a single radial plane. Vdmp: 平均内径变动量： mean bore diameter variation. Bs: 内圈单一宽度偏差 .Deviation of a single width of the inner ring. B: 内圈公称宽度。 Width of inner ring, nominal. D: 轴承公称外径。 Bearing outside diameter, nominal. Dmp: 单一平面平均外径偏差。 Single plane mean outside diameter deviation. VDp: 单一径向平面外径变动量。 Outside diameter variation in a single radial plane. VDmp: 平均外径变动量。 Mean outside diameter variation. Cs: 外圈单一宽度偏差。 Deviation of a single width of the outer ring. C: 外圈公称宽度。 Width of ourer ring, nominal. Ts: 角接触关节轴承实际宽度偏差。Actual deviation of width of the angular contact spherical plain bearing. △Hs: 推力关节轴承实际高度偏差。 Actual deviation of height of the spherical plain thrust bearing. hs, △ h1s: 杆端关节轴承或球头杆端关节轴承中心高偏差。 Center height deviation of rodends or ball joint rod ends 内圈 Inner ring d mm △ dmp △ dmp* vdp vdmp Vdp* Vdmp* △ Bs △Bs* 超过 到 max min max min max max max max max min max min over incl. - 18 0 -8 18 0 8 6 18 14 0 -120 0 -180 18 30 0 -10 21 0 10 8 21 16 0 -120 0 -210 30 50 0 -12 25 0 12 9 25 19 0 -120 0 -250 520 80 0 -15 30 0 15 11 30 22 0 -150 0 -300 80 120 0 -20 35 0 20 15 35 26 0 -200 0 -350 120 180 0 -25 40 0 25 19 40 30 0 -250 0 -400 180 250 0 -30 46 0 30 23 46 35 0 -300 0 -460 250 315 0 -35 52 0 35 26 52 39 0 -350 0 -520 315 400 0 -40 57 0 40 30 57 43 0 -400 0 -570 400 500 0 -45 - - 45 34 - - 0 -450 - - 500 630 0 -50 - - 50 38 - - 0 -500 - - 外圈 Outer ring D mm △ Dmp um Vdp um Vdmp um △Cs um 超过 over 到 incl. max min max max max min - 18 0 -8 10 6 0 -240 18 30 0 -9 12 7 0 -240 30 50 0 -11 15 8 0 -240 50 80 0 -13 17 10 0 -300 80 120 0 -15 20 11 0 -400 120 150 0 -18 24 14 0 -500 150 180 0 -25 33 19 0 -500 180 250 0 -30 40 23 0 -600 250 315 0 -35 47 26 0 -700 315 400 0 -47 53 30 0 -800 400 500 0 -45 60 34 0 -900 500 630 0 -50 67 38 0 -1000 630 80