毕业设计说明书污水厂CASS工艺.docxVIP

PAGE PAGE # / 35 XX某经济开发区污水处理厂设计 摘要：本设计主要是XX市某经济开发区污水处理厂的设计，该污水厂位于经济 开发区，根据对原水水质的分析，以及参考大量的污水处理资料，综合考虑技术、经济 等因素，最终釆用现行的SBR变形形式CASS工艺。CASS是周期循环活性污泥法的简 称，乂称为循环活性污泥工艺，是在SBR的基础上发展起来的，即在SBR池内进水端 增加了一个生物选择器，实现了连续进水（沉淀期、排水期仍连续进水），间歇排水。该 污水厂设计的流程为进水一粗格栅一提升泵房一细格栅一平流沉砂池-CASS池一普快 滤池一消毒池一出水。污泥的处理流程为CASS-污泥提升泵房一储泥池一浓缩池。该厂 出水达到设计要求。 关键词：污水处理厂；CASS；污泥处理 Factory design of an Economic Development ZoneWastewater Treatment in Nantong Abstract：This design is the design of wastewater treatment plant of a economic development zone of Nantong City, the sewage treatment plant is located in the economic development zone, based on the analysis of the raw water quality, sewage and reference data processing large, prehensive consideration of technical economic and other factors, the current SBR deformation form of CASS process. CASS is a cyclic activated sludge method abbreviation, also known as cyclic activated sludge technology, is in the SBR developed on the basis of SBR, namely in the pool water inlet end adds a biological selector, realizes continuous water (precipitation, drainage period is still continuous, intermittent drainage.). The design of wastewater treatment plant process water, coarse grid, pumping station, fine grid, advection sedimentation tank, CASS tank t Piikuai filter, disinfection pool, water. Treatment process of sludge is CASS, sludge pumping station, sludge storage tank, concentrated pool. The effluent can meet the design requirements. Key words: Sewage treatment plant; CASS;sludge disposal 摘要I Abstractll 1绪论1 1. 1课题研究意义1 2污水厂概况1 2.1地理位置及气候1 2.2设计规模及进出水水质2 2.3处理程度的计算2 3城市污水处理设计2 3.1污水处理工艺流程选择2 3.2工艺比较3 321氧化沟方案3 322 CASS工艺方案4 3.3方案的确定6 X艺流程图6 4污水处理构筑物的设计说明7 4.1粗格栅的设计7 4.1.1格栅尺寸7 4.1.2通过格栅的水头损失h】8 4.1.3栅后槽总高度H8 4.1.4栅槽总长度L8 4.1.5每日栅渣量 W9 4.1.6格栅的选择9 4.2提升泵房10 4.3细格栅10 43.1细格栅的隔栅尺寸10 4?3?2通过格栅的水头损失lull 4.3.3栅后槽总高度H11 43.4栅槽总长度L11 4.3.5每日栅渣量VV12 4.4平流式沉砂池12 功能：12 4.4.2设计计算13 4.4.3主要工程内容14 CASS生化池15 CASS 的功能 15 4.5.2设计计算15 4.6滤池设计计算20 4.7接触消毒池与加氯间21 4.7.1设计说明：21 4.7