- 1、本文档共37页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
摘要
PAGE IV
基于PLC的自动门控制系统设计
摘 要
随着科学技术的不断发展,自动门系统已开始应用于大型公司、科研所、政府机关等保密性较强的单位。为增强自动门运行的可靠性,本设计提出了一种FX232MR可编程控制器(PLC)与变频器控制的自动门控制系统,设计中采用两个感应探测器(门内和门外)、一些开关及传感器作为此系统的输入设备,变频器用来调节门体速度,并分析了该控制系统的工作原理及系统的硬件组成,分析了人体感应探测、自动门运行位置检测、门运行障碍检测等控制电路的工作过程,对PLC的选型、变频器的选型、I/O点的确定及自动门的动作过程等方面进行了详细阐述。结合PLC的运行特点,对控制系统的工作流程作了合理的优化。在此基础上,给出了控制系统软件设计的程序流程图、顺序功能图、外部端子接线图及PLC控制梯形图等。本设计介绍应用可编程控制器取代传统的继电器、接触器控制系统,实现自动门控制的过程。
关键词:自动门,可控制编程器,梯形图,变频控制
Design of Automatic Door
Control System Based on PLC
ABSTRACT
With the continuous development of science and technology, automatic door system has been applied to large companies, research institutes, government agencies and other units are highly confidential. To enhance the reliability of automatic door operation, this design presents a FX2 -32MR programmable logic controller (PLC) and the inverter control automatic door control system, the design uses two sensor probes (door and door outside), some switches and sensors as the system input device, the drive door is used to adjust the speed, and analyzes the working principle of the control system hardware components and systems, analysis of the human body detection sensors, automatic door operation position detection, the door obstacle detection and other control circuit to run the working process, the selection of the PLC, inverter selection, I / O points of the action to identify and automatic doors and other aspects of the process in detail. With PLCs operating characteristics of the control system were reasonable workflow optimization. On this basis, given the process control system software design flow, sequential function chart, the external control terminal wiring diagram and PLC ladder and so on. Describes the application of the programmable controller designed to replace traditional relay, contactor control systems, automatic door control process.
KEY WORDS: Automatic Doors,Control Programming,Ladder,Drive
前言
目 录
TOC \o 1-3 \h \z \u 前 言 1
第1章 概述 3
1.1 研究背景和研究意义 3
您可能关注的文档
- 基于ms51单片机的4个16x16点阵led电子显示屏的设计.doc
- 基于msisa2006网络流量计费系统.doc
- 基于msp430单片机的壁挂式空调风门运动控制系统设计.doc
- 基于multisim10的am和dsb振幅调制器仿真设计.doc
- 基于NRF905射频收发单片机系统.doc
- 基于NS的光突发交换仿真平台设计.doc
- 基于pc机的lcd实时显示控制系统设计.doc
- 基于PEBI网格的低渗油藏水平井压裂裂缝参数优化.doc
- 基于PHP的多用户博客系统的设计.doc
- 基于php和mysql的新闻信息综合管理系统的设计与实现.doc
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)