CAXA制造工程师之--平面区域粗加工.docVIP

CAXA制造工程师之--平面区域粗加工 平面区域粗加工 ? 加工精度 轮廓参数 ? 余量 给轮廓加工预留的切削量。 ? 斜度 以多大的拔模斜度来加工。 ? 补偿 有三种方式。ON：刀心线与轮廓重合。TO：刀心线未到轮廓一个刀具半径。PAST：刀心线超过轮廓一个刀具半径。 岛屿参数 ? 余量 给轮廓加工预留的切削量。 ? 斜度 以多大的拔模斜度来加工。 ? 补偿 有三种方式。ON：刀心线与岛屿线重合。TO：刀心线超过岛屿线一个刀具半径。PAST：刀心线未到岛屿线一个刀具半径。 标识钻孔点 选择该项自动显示出下刀打孔的点。 O1200 (NC0006,2010-11-12 ,19:52:54.515 ) ($stockbase=-50.,-40.,0. ) ($stockbox=50.,40.,30. ) (=========LoadTool=====1===========) ($tool_nameD12$tool_rad=6 $tool_corner_rad=0 ) ($tool_num=2 $tool_cutcom_reg=2 $tool_cut_length=40 ) (pathCoordinate:) ($pathcoord0=0.,0.,0. ) ($pathcoordx=10.,0.,0. ) ($pathcoordy=0.,10.,0. ) 刀具直径12，行距9 N8 T2 M6 N10 G90 G54 G0 X-30. Y-23.8 S3000 M N12 G43 H0 Z100. M07 N14 Z35. N16 G1 Z25. F100 N18 G17 G2 X-33.8 Y-20. I0. J3.8 F10 N20 G1 Y20. N22 G2 X-30. Y23.8 I3.8 J0. N24 G1 X30. N26 G2 X33.8 Y20. I0. J-3.8 N28 G1 Y-20. N30 G2 X30. Y-23.8 I-3.8 J0. N32 G1 X-30. N34 X-15. Y-21.2 N36 X15. N38 G3 X26.2 Y-10. I0. J11.2 N40 G1 Y10. N42 G3 X15. Y21.2 I-11.2 J0. N44 G1 X-15. N46 G3 X-26.2 Y10. I0. J-11.2 N48 G1 Y-10. N50 G3 X-15. Y-21.2 I11.2 J0. N52 G1 X-30. Y-23.9 N54 G2 X-33.9 Y-20. I0. J3.9 N56 G1 Y20. N58 G2 X-30. Y23.9 I3.9 J0. N60 G1 X30. N62 G2 X33.9 Y20. I0. J-3.9 N64 G1 Y-20. N66 G2 X30. Y-23.9 I-3.9 J0. N68 G1 X-30. N70 X-15. Y-21.1 N72 X15. N74 G3 X26.1 Y-10. I0. J11.1 N76 G1 Y10. N78 G3 X15. Y21.1 I-11.1 J0. N80 G1 X-15. N82 G3 X-26.1 Y10. I0. J-11.1 N84 G N86 G3 X-15. Y-21.1 I11.1 J0. N88 G1 Z35. F100 N90 G0 Z100. N92 X-30. Y-23.8 N94 Z30. N96 G1 Z20. N98 G2 X-33.8 Y-20. I0. J3.8 F1000 N100 G1 Y20. N102 G2 X-30. Y23.8 I3.8 J0. N104 G1 X30. N106 G2 X33.8 Y20. I0. J-3.8 N108 G1 Y-20. N110 G N112 G1 X-30. N114 X-15. Y-21.2 N116 X15. N118 G3 X26.2 Y-10. I0. J11.2 N120 G1 Y10. N122 G3 X15. Y21.2 I-11.2 J0. N124 G1 X-15. N126 G3 X-26.2 Y10. I0. J-11.2 N128 G1 Y-10. N130 G3 X-15. Y-21.2 I11.2 J0. N132 G1 X-30. Y-23.9 N134 G2 X-33.9 Y-20. I0. J3.9 N136 G1 Y20. N138 G2 X-30. Y23.9 I3.9 J0. N140 G1 X30