LED流水灯线路图.docxVIP

附件： 图1-1 LED灯闪亮时间间隔600ms电路图 程序1-1： ORG 0000H START: CLR P1.0 LCALL DELAY SETB P1.0 LCALL DELAY LJMP START DELAY : MOV R5,#60 //延时子程序，延时600ms D1: MOV R6,#20 D2: MOV R7,#248 DJNZ R7,$ DJNZ R6,D2 DJNZ R5,D1 RET END  图2-1 LED流水灯线路图 程序2-1： ORG 0000H LJMP MAIN ORG 0100H DELAY1: MOV R7,#200 D1:MOV R6,#200 D2:DJNZ R6,D2 DJNZ R7,D1 RET DELAY2: MOV R7,#250 D4:MOV R6,#250 D5:DJNZ R6,D2 DJNZ R7,D4 RET D3: MOV P2,A LCALL DELAY1 RL A MOV P2,A LCALL DELAY1 DJNZ R5,D3 LCALL DELAY1 MOV P2,#0 LCALL DELAY2 RET MAIN: MOV R5,#7 MOV A, LCAll D3 LJMP MAIN END 图3-1 LED数字显示倒计时电路图 程序3-1： ORG 0000H LJMP MAIN ORG 0100H CHART:DB 0C0H,0F9H,0A4H,0B0H,99H,92H,82H,0F8H,80H,90H DELAY: MOV R7,#10 DEL1:MOV R6,#200 DEL2:MOV R5,#248 DJNZ R5,$ DJNZ R6,DEL2 DJNZ R7,DEL1 RET LOOP: MOV DPTR,#CHART MOV A,R2 MOVC A,@A+DPTR MOV P2,A LCALL DELAY DEC R2 DJNZ R1,LOOP RET MAIN: MOV R1,#10 MOV R2,#9 LCALL LOOP LJMP MAIN END  图4-1 LED加减按键电路图 程序4-1： ORG 0000H LJMP START ORG 0030H START: MOV R2, #1 LOOP: CALL DISP JB P1.6, NEXT CALL DL10MS JB P1.6, NEXT JNB P1.6, $ DJNZ R2, NEXT MOV R2, #10 NEXT: JB P1.7, LOOP CALL DL10MS JB P1.7, LOOP JNB P1.7, $ INC R2 CJNE R2, #11, LOOP JMP START ; DISP: MOV A, R2 DEC A MOV DPTR, #TAB MOVC A, @A + DPTR MOV P2, A RET DL10MS: MOV R6, #20 DJNZ R7, $ DJNZ R6, $ - 2 RET ; TAB: DB 0C0H, 0F9H, 0A4H, 0B0H, 99H DB 92H, 82H, 0F8H, 80H, 90H ; END 图5-1 电压超限预警电路图 程序5-1： ORG 0000H NOLED: MOV P2,#0 START: JB P1.0,LED CALL NOLED LED: MOV P2,#1 JMP START END  图6-1 电压超限预警报警显示电路图 程序6-1： #include reg52.h #define uchar unsigned char #define uint unsigned int //=========================== //ADC0809相关引脚定义 //=========================== #define ADC_DATA P1 sbit ADC_EOC = P3^3; sbit ADC_CLK = P3^4; sbit ADC_START = P3^6; sbit ADC_OE = P3^7; //=========================== //4位