JBT 7186.4-1995冲模滚动导向钢板模座 四导柱上模座.pdf

中华人民共和国机械行业标准JB/T 7186.4—95冲模滚动导向钢板模座四导柱上模座主题内容与适用范围本标准规定了冲模滚动导向钢板模座四导柱上模座的技术条件。，尺寸规格、材料、热处理要求及标记。本标准适用于冲模滚动导向钢板模架。2 引用标准JB/T7188冲模钢板模架零件技术条件GB 699优质碳素结构钢技术条件GB 8845冲模术语3模座的技术条件和尺寸规格3.1技术条件按JB/T 7188的规定。3.2尺寸规格见图和表。Af.6ETATB图机械工业部1995-03--21批准1995--07—01实施64 JB/T 7186. 4—95表mm凹棋周界D(R?)D (H?)L1BrHFsS1LB基本尺寸极限偏差基本尺寸极限偏差StMXt160160250z.4080:17044452002002503240120+0:025+ 0. 025.1704500250100250.2503240170.17044453153152654045225-1755255+ 0. 030155+0.0304004002654045.310-0M12X25:17552552402002002653240+0..025+0. 025120 .$185444500.2502502804045160:1905255100.1253153152804045225-190:52551554004002804045190525524050050028040454101905255.330250250315404516022552551003153153154045225225525515540016040031540453102255255230M12×255005003154045410225 .5255330630630355555202456689430250250355.4045160265+ 0. 0305255+0.030100003153153554045225265525515540020040035540453102655255230500500400505539029066683006306304005055.5202906668430M16× 3031531542540452253355255150400400450.5055290M12X2534066682005002505004505055062340668930063063045050555203406668430M16× 30800800450505569034066686004004005305055290420666820050050056050593744347880280315:6306305605063504434.7880380800800560896367443478000++0. 030M16X308055005000500630506337450478082806306306309635045047880380800400800630.6363674504 78805501000100067080+0.03570860530+0. 035M20X35069570065 JB/T 7186. 4--95续表D(R?)D,(H?)回模]界HS.MxtB.FsS1基本极限基本极限1L尺寸尺寸偏差+ 0. 030+0.03078803806307506363504624630500610069550080080075080660:70M20 X 35SEO 0+.96+0. 035:s1006700100010007508070860007609095700100090008 7086010006304 材料和热处理要求4. 1材料45 钢 GB 699.4. 2·热处理要求45 钢调质 HRC26~30.标记5本标准规定的模座标记由下列要素组成：上模座b.模座的凹模周界 LXB.模座厚度 H,c.d.材料;本标准编号。e.示例：凹模周界 L=400 mm、B250 mm、模座厚度 H=40 mm、材料为 45 钢的四导柱上模座的标记如下：上棋座 400×250×4045JB/T 7186. 4