ansys内部例题详解.docxVIP

郑重申明：本人能力有限，文中不可避免会有错误，欢迎朋 友们批评指正，希望大家相互提高，呵呵，谢谢啦！ Sample Rigid Body Dynamic Analysis 刚体动力学分析实例 This sample analysis demonstrates how to model a flexible component in ANSYS and export the flexible body information to a file for use in ADAMS. The example also provides brief instructions on how to perform the rigid body dynamic analysis in ADAMS, and details on how to transferthe loads from ADAMS to ANSYS in order to perform a stress analysis. 该实例演示了如果在ANSYS 中制作柔性部件及输出可在ADAMS 中使用的柔性体信息文件。同样该例子也提供了有关于在 ADAMS 中进行动力学分析的简单介绍，和如何将载荷信息从 ADAMS 转换到 ANSYS 中进行应力分析的详细介绍。 Problem Description 问题描述 In the linkage assembly shown below, Link3 is a flexible component. Link3 is modeled as a rectangular rod in ANSYS using SOLID45 elements. The joints in ADAMS will be attached to interface points (nodes) at the middle of the holes at either end of Link3. These middle points are connected to the cylindrical joint surfaces by a spider web of BEAM4 elements. 联动装置装配如下图所示，连杆 3 是一个柔性部件，为矩形杆件在 ANSYS 中采用SOLID45 单元构造。ADAMS 中连接铰将连接在位于杆两端的孔中心接触节点上。这些节点会通过 BEAM4 单元构造的蜘蛛网格与圆柱铰表面连接。 Figure 12.5: Linkage Assembly 联动装置转配图 Problem Specifications 问题说明 The figure below shows the Link3 component as it is modeled in ANSYS. Figure 12.6: Link3 Component The following are dimensions and properties for the Link3 component. 杆 3 的尺寸及性能如下 Radius of holes (radh) = 6mm 孔径=6mm Width of rectangular rod (width) = 25mm 矩形杆件宽度=25mm Thickness of rectangular rod (thick) = 10mm 杆件厚度=10mm Length of rectangular rod (length) = 300mm + 4*Radius of holes = 324mm 杆件长度=300+4*孔径=324mm Youngs modulus for rod = 7.22 x 104 MPa 杆的弹性模量=7.22 x 104 MPa Poissons ratio for rod = 0.34 杆的泊松比=0.34 Density of rod = 2.4 x 10-9 tons/mm3 杆的密度=2.4 x 10-9 tons/mm3 （注意单位是吨/立方毫米） Youngs modulus for beams = 2.1 x 105 MPa 梁的弹性模量=2.1 x 105 MPa （孔内蜘蛛网格是用梁单元构造的） Poissons ratio for beams = 0.3 梁的泊松比=0.3 Density of beams = 0.1 x 10-9 tons/mm3 梁的密度= 0.1 x 10-9 tons/mm3 Command Input 命令输入窗口例子中采用的是命令语句，对于我们这样的初学者可能还是习惯使用图形界面，绿色语句是相应的在图形交互界面的使用方式。 命令输入窗口 童鞋们也可以将这