NPT管螺纹表完整版.doc

NPT：美国标准的60度锥管螺纹 2009年07月04日 星期六 15:45 NPT：美国标准的60度锥管螺纹 ????????? 美制一般密封管螺纹的基本尺寸： 尺寸代号 牙数n 螺距P 牙型高度h 基准平面内的基本直径 基准距离L1 装配余量L3 外螺纹小端面内的基本小径 大径d=D 中径d1=D2 小径d1=D1 mm 圈数 mm 圈数 mm mm 1/16 27 0.941 0.752 7.894 7.142 6.389 4.32 4.064 3 2.822 6.137 1/8 27 0.941 0.752 10.242 9.489 8.737 4.36 4.102 3 2.822 8.481 1/4 18 1.411 1.129 13.616 12.487 11.358 4.10 5.785 3 4.233 10.996 3/8 18 1.411 1.129 17.055 15.926 14.797 4.32 6.096 3 4.233 14.417 1/2 14 1.814 1.451 21.224 19.772 18.321 4.48 8.128 3 5.443 17.813 3/4 14 1.814 1.451 26.569 25.117 23.666 4.75 8.618 3 5.443 23.127 1 11.5 2.209 1.767 33.228 31.461 29.694 4.60 10.160 3 6.626 29.060 11/4 11.5 2.209 1.767 41.985 40.218 38.451 4.83 10.668 3 6.350 37.788 11/2 11.5 2.209 1.767 48.054 46.287 44.520 4.83 10.668 3 6.350 43.853 2 11.5 2.209 1.767 60.092 58.325 56.558 5.01 11.065 3 6.350 55.867 21/2 8 3.175 2.540 72.699 70.159 67.619 5.46 17.335 2 6.350 66.535 3 8 3.175 2.540 88.608 86.068 83.528 6.13 19.463 2 6.350 62.311 31/2 8 3.175 2.540 101.316 98.776 96.236 6.57 20.860 2 6.350 94.932 4 8 3.175 2.540 113.973 111.433 108.893 6.75 21.431 2 6.350 107.554 5 8 3.175 2.540 140.952 138.412 135.872 7.50 23.812 2 6.350 134.384 6 8 3.175 2.540 167.792 165.252 162.712 7.66 24.320 2 6.350 161.191 8 8 3.175 2.540 218.441 215.901 213.361 8.50 26.988 2 6.350 211.673 10 8 3.175 2.540 272.312 269.772 267.232 9.68 30.734 2 6.350 265.311 12 8 3.175 2.540 323.032 320.492 317.952 10.88 34.544 2 6.350 315.793 14O.D. 8 3.175 2.540 354.904 352.364 349.824 12.50 39.688 2 6.350 347.345 16O.D. 8 3.175 2.540 405.784 403.244 400.704 14.50 46.038 2 6.350 397.828 18O.D. 8 3.175 2.540 456.565 454.025 451.485 16.00 50.800 2 6.350 448.310 20O.D. 8 3.175 2.540 507.246 504.706 502.166 17.00 53.975 2 6.350 498.792 24O.D. 8 3.175 2.540 608.608 606.068 603.528 19.00 60.325 2 6.350 599.758 ??? 注： ① 可参考表中的最右边一列数据选择攻丝前的麻花钻直径；??????????? ②?? 螺纹收尾长度（V）为3.47 P；??????????? ③?? O.D.是英文管子外径（outside diameter）的缩写。