毕业论文：滑轮注塑模具的设计和制造.docVIP

PAGE  滑轮注塑模具的设计和制造 摘 要 模具是利用其特定形状去成型具有一定的形状和尺寸制品的工具。在各种材料加工工业中广泛的使用着各种模具。 滑轮设计时为节约资源，应采用一模两腔的方式制造，因为滑轮为圆形的侧抽芯，采用半开模的方式来制造最为合适。在制造前要先计算好塑件的受力状况，最合适的浇口位置，并进行校核。并且用PROE来演示开模。 根据塑件的体积，最大受力等来选择合适的注塑机，并根据注塑机来确定交口套，定位圈的尺寸，最后进行校核。确定注塑结构后再根据标准来确定每个零件的尺寸进行装配。 关键词：模具 滑轮PROE演示 ABSTRACT PAGE ii ABSTRACT Mold is the use of their specific shape to the shape of a certain shape and size of tool products. Processing industry in a variety of materials widely used in a variety of molds. The pulley designs when is the nurse resources, should use a mold two cavity the way manufactures, because the pulley is the circular side pulls out the core, uses half die sinking the way to make appropriately. Must calculate first before the manufacture models the stress condition, the most appropriate runner position, and carries on the examination. and demonstrates the die sinking with PROE. According to models a volume, the biggest stress and so on chooses the appropriate injection molding machine, and according to the injection molding machine determined that hands over the mouth wrap, binding rings size, finally carries on the examination. After determination injection molding structure, according to the standard determined again each components the size carries on the assembly. Key words: Plastic mold Pulley The Demo of PROE   PAGE 3 目 录 第一章 绪论┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 1 1.1 立项背景┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 1 1.2 材料分析┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 2 1.3 一般性能┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 3 1.4 塑件材料成型性能┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈4 第二章 注塑设备的选择┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈5 2.1估算塑件体积和质量┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.2校核┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.2.1最大注射量的校核 ┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.2.2 注射压力的校核┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.2.3锁模力的校核┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.2.4 开模行程的校核 ┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 2.3注射机的选择 ┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 5 第三章 模具结构的设计┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 7 3.1 总体设计思路┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈┈ 7 3.1.1 模具基本结构的选择┈┈┈┈┈┈┈┈┈┈┈┈┈┈