某高速公路线路、路基毕业设计.docVIP

某高速公路线路、路基毕业设计 内容简介 本道路起点位于厦门市同安镇，桩号K0+000，终点位于厦门市集美镇，桩号K3+927.706，路线全长3.927706公里。平面线形均能满足高速公路相关技术标准。全线共设交点3个，平均每公里交点个数为0.764个。平曲线总长1.803731Km，占路线总长的45.92%。平曲 ... p 内容简介/p p 本道路起点位于厦门市同安镇，桩号K0+000，终点位于厦门市集美镇，桩号K3+927.706，路线全长3.公里。 平面线形均能满足高速公路相关技术标准。全线共设交点3个，平均每公里交点个数为0.764个。平曲线总长1.Km，占路线总长的45.92%。平曲线最小半径R=875.838m。 全线纵断面线形均能满足高速公路相关技术标准。全线纵坡变更次数8次，平均每公里变更2.037次,竖曲线总长2.Km，占路线总长的66.96%，最大纵坡3.2447%，竖曲线最小半径：凸曲线R=6500m，凹曲线R=4318.313m。路基宽度：路基总宽26m。其中行车道宽15m，路幅布置如下： 0.75m（土路肩）+3m（硬路肩）+7.5m（行车道）+0.75m（路缘石）+2m（中央分隔带）+0.75m（路缘石）+7.5m（行车道）+3m（硬路肩）+0.75m（土路肩）。 /p p路基标准横断面br /路面结构图br /横断面图（4张）br /纵断面图（4张）br / /pP/P p摘要br / 本文介绍了选煤的意义和作用，同时介绍了基于的自动选煤系统的实现。为了保证输送带运输的安全可靠运行，达到减人提效的目的，应用可编程控制器，辅以必要的装置，设计了输送带自动运输系统。煤块从煤仓出来经过1#输送带送到振动筛，在经过振动筛筛选后小的煤块漏到4#输送带送进洗煤厂，大的煤块则经过3#输送带运送到粉碎机，经过粉碎机粉碎后在经过2#输送带到达4#输送带，再输送到洗煤厂。粉碎机由三个限位开关监管，若煤块过多，则将信号传给由PLC控制的变频器，变频器则调节1#输送带的给煤速度。启动有手动和自动两种，自动可自动完成输送任务；手动可单独运行单一电机，达到维修目的。br / br / 关键词 ：nbsp; PLC，输送带，振动筛，粉碎机，变频器br / br / Abstractbr / This article describes the significance and usage of coal preparation, also introduced automated Preparation System based on PLC. To ensure safe and reliable, and to realize the aim of high efficiency we designed the conveyor belt automatic transport system base on PLC programmable controller, addition with the necessary equipment. Coal from the bunker out of conveyor belt through 1 # sent vibrating screen, vibrating screen, after screening a small leak to 4 # coal conveyor belt feeding coal washing plant, a large coal conveyor belt is transported through the 3 # grinding machine, after smash after arrival, after 2 # and 4 # conveyor belts, territory to coal washing plant. Mill consists of three limit switch monitoring, if too much coal, it will signal transmitted by the PLC-controlled inverter, inverter # 1 is regulating the speed coal conveyor belt. Start with manual or automatic, automatic transmission tasks can be done automatically; manual single motor can be run separately, to maintenance purposes. b