典型零件(EM170A-01001)工艺过程及工装设计.doc

典型零件(EM170A-01001)工艺过程及工装设计.doc

  1. 1、本文档共49页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
摘 要 本次设计是在我们学完了大学的全部基础课、技术基础课以及专业课之后进行的,这是我们在进行毕业之前,对所学各课程的一次深入的综合性的总复习,也是一次理论联系实际的训练。 本人的毕业设计是对典型零件的工艺过程和工装进行设计,其典型零件是EM170A-01001型内燃机机体。在设计中主要是进行零件的毛坯尺寸的计算、工艺过程的设计、切削用量的计算和专用夹具的设计。 机体类零件在整个机器中的作用是:承载曲轴及其内部传动装备,并使其保持交好的相对位置。零件的下底面与机座相配合,其他平面与汽缸盖、端盖等配合,孔系主要与曲轴轴承和汽缸等配合。根据以上的作用来设计机体的加工过程和顺序将得到较好的工艺要求。 关键词:设计,典型零件,机体,工艺 ABSTRACT This design is finished in our study based on all university courses, technical and professional course in basic subjects after the It is carrying out before graduating, on the school curriculum an in-depth comprehensive review of the total. it is also a theory with practical training. I graduated from the design of the components of the typical process for the design and the fixtures, A typical parts of EM170A - 01001-Engine Block. In the design of the main components is the size of the rough calculation, the design process, Cutting the amount of calculation and special fixture design. Body parts in the entire apparatus of the role is : internal bearing crankshaft and transmission equipment. and enabling it to maintain a relatively good position pay. Under bottom parts and machine matched with the other plane cylinder hoods, etc. Cover with, Holes and crankshaft main bearings and cylinder and other tie. According to the above effect to the body of the design process and the processing sequence will be better technological requirements. Keywords: Design, the typical parts, the body, crafts 目 录 中文摘要 Ⅰ 英文摘要 Ⅱ 第1章 生产纲领及生产类型 1 第2章 零件的分析 2 第3章 工艺规程的设计 3 3.1 确定毛坯的制造形成 3 3.2 基准的选择 3 3.2.1粗基准的选择 3 3.2.2精基准的选择 3 3.3制订工艺路线 3 3.4机械加工余量、工序尺寸及毛坯尺寸的确定 8 3.5确定切削用量及基本工时 11 第4章 专用夹具的设计 37 4.1问题的指出 37 4.2夹具设计 37 4.2.1定位基准的选择 37 4.2.2切削力及夹紧力的计算 37 参考文献 40 致谢 41 附录A:组合铣床示意图 42 第一章 生产纲领及生产类型 产品的生产纲领是指包括备品和废品在内的该产品的年产量。零件的生产纲领可按下式计算: (1—1) 式中 ——零件的生产纲领(件/年); ——机器产品的年产量(台/年); ——每台产品中该零件的数量(件/台); ——备品百分率; ——废品百分率。 则零件的生产纲领为: (件/年) 根据生产 、产品复杂程度和重量的不同,可分为单件生产、成批生产(又可分为小批、中批和大批)和大量生产三种生产类型,见下表: 表1—1 生产类型和生产纲领的关

文档评论(0)

***** + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档