英文文献—Welding on Engines with Electronic Controls.docVIP

下载本文档

8
0
约8.88千字
约 4页
2017-09-06 发布于河南
举报
版权申诉

英文文献—Welding on Engines with Electronic Controls.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

附录 1. Welding on Engines with Electronic Controls Because the strength of the frame may decrease, some manufacturers do not recommend welding onto a chassis frame or rail. Consult the OEM of the equipment or your Caterpillar dealer regarding welding on a chassis frame or rail. Proper welding procedures are necessary in order to avoid damage to the engine’s ECM, sensors, and associated components. When possible, remove the component from the unit and then weld the component. If removal of the component is not possible, the following procedure must be Followed when you weld on a unit that is equipped with a Caterpillar Electronic Engine. The following procedure is considered to be the safest procedure to weld on a component. This procedure should provide a minimum risk of damage to electronic components. 2. Neutral Connections The generators with grounded configuration usually have the neutral grounded when the generator is installed. However, there are some cases when definite measures can be taken in order to prevent ground faults on the load side. The purpose of the grounding of the neutral is to prevent load side equipment damage. The purpose of the grounding of the neutral is also to prevent harm to personnel. If the neutral wire is grounded and one of the phase leads becomes grounded, the excessive current will open a load circuit breaker in order to isolate the fault. The excessive current will collapse the generator voltage, if the circuit breaker does not trip first. The result depends on the particular generator electrical characteristics, type of fault, and trip rating of the circuit breaker. An undervoltage device may be required in order to provide an adequate short circuit protection. There are some instances in which it is undesirable to ground the neutral wire. An ungrounded generator neutral lead is acceptable in the applications in which definite measures have been taken in order to prevent grounds to the phase leads. An example of such measures are