深筒件的冲压工艺及模具设计【优秀机械专业论文】【全套带CAD图】.doc

精品机械毕业设计 答辩CAD图纸资料 优秀通过答辩 摘 要 冷冲压是利用安装在压力机上的冲模对材料施加压力，使其产生分离或塑性变形，从而获得所需要零件的一种压力加工方法。 冷冲压模具工业是国民经济的基础工业，是国际上公认的关键工业。模具生产技术水 平的高低是衡量一个国家产品制造水平高低的重要标志，它在很大程度上决定着产品的质 量，效益和新产品的开发能力。振兴和发展我国的模具工业，正日益受到人们的关注。 本设计的课题是深筒件的冲压工艺及模具设计，零件采用08钢，主要用先拉深成底部带有预冲孔的阶梯形圆筒件，然后再翻遍。用到的工序有落料拉伸工序、第二次拉伸工序、第三次拉伸工序及整形、冲翻边底孔ф11 工序、翻边工序、冲3个小孔工序、切边工序这些工序流程。本次设计设计了2副模具，一副落料拉伸模：模架采用后侧导柱导向模架；一副为冲3个小孔的冲孔模。零件采用单排方式，板材尺寸为1.5×900×1800mm。 关键词: 冷冲压；深筒件；模具设计 Abstract Cold stamping is using presses installed in the die pressure on the material, make its produce a separation or plastic deformation, obtained from the required parts of a pressure processing method. Cold stamping die industry is the foundation of the national economy industry, is internationally recognized as one of the key industries. Mold production technology level of high and low is a measure of a national product manufacture level of important symbol, it largely determines the quality of products, and new product development capability. Revitalization and development of mould industry in China, are increasingly being peoples attention. This design topic is Cold stamping technology and die design of tube parts, parts using 08 steel, mainly used to pull with pre punching deep into the bottom of the step cylinder, and then went through. Use process with blanking stretching process, the second stretching process, the third stretching process and plastic and flanging bottom hole ф 11 work procedure and three holes, flanging process, trimming process these processes. The two vice mould design design, a blanking tensile mold: mold frame with side guide column guide die set; A pair of blunt three holes of punching die. Parts adopt single method, board size is 1.5 * 900 * 1800 mm, Key words: cold stamping；tube pieces；the mold design 目 录 摘 要 IV Abstract V 目 录 VI 1 绪 论 1 1.1?本课题的研究内容和意义 1 1.2 国内外的发展概况 1 1.3 本课题应达到的要求 2 2 深筒件的分析 3 2.1 深筒件的设计要求 3 2.2 深筒件的尺寸分析 3 2.3 深筒件材料的选用 3 2.4 深筒件圆孔加工计算 4 2.5 深筒件加工工艺的分析 4 3 工艺方案的选择 5 3.1 毛坯直径计算 5 3.1.1 翻