实验二一面两空定位铣削侧面的加工位置精度分析.docVIP

实验二 一面两空定位铣削侧面的加工位置精度分析 实验数据 序号 孔径d1 孔径d2 L L2 L3 a a角度 L2’ L3’ a’ a角度 1 25.9 25.2 50 13 20 0.139095941 7.969610394 18 22 0.079829986 4 2 23.9 24 50 22 24 0.039978687 2.290610043 16 33 0.327738507 18 3 23.5 24 50 12 11 0.019997334 1.145762838 35 38 0.059928155 3.433630362 4 22.4 22 50 19 15 0.079829986 424 43 020 5 23.4 24 50 7 14 0.139095941 7.969610394 25 40 0.291456794 16 6 22.5 22.2 50 4 0 0.079829986 420 22 0.039978687 2.290610043 7 23.9 24.2 50 22 18 0.079829986 427 42 0.291456794 16 8 23.8 24 50 13 11 0.039978687 2.290610043 43 32 0.216550305 12 9 23.2 24.2 50 20 17 0.059928155 3.433630362 33 30 0.059928155 3.433630362 10 22.3 23 50 17 9 0.158655262 9.090276921 25 37 0.235544981 13 11 23.2 21.7 50 19 39 0.380506377 2123 35 0.235544981 13 12 24 24.1 50 7 1 0.119428926 6.842773413 18 30 0.235544981 13 13 23.1 24.2 50 12 0 0.235544981 1317 37 0.380506377 21 14 21.3 23.2 50 3 3 0 0 25 23 0.039978687 2.290610043 15 24.2 22.9 50 10 12 0.039978687 2.290610043 30 34 0.079829986 4 16 24.4 24.1 50 3 15 0.235544981 1328 30 0.039978687 2.290610043 17 24 24.3 50 21 32 0.216550305 1221 34 0.254368059 14.5742162 18 23.1 21.2 50 28 15 0.254368059 14.5742162 19 30 0.216550305 12 19 22 23.4 50 21 41 0.380506377 2127 41 0.273008703 15 20 24.3 23.8 50 25 42 0.327738507 1829 37 0.158655262 9.090276921 21 24.4 24 50 37 38 0.019997334 1.145762838 23 23 0 0 22 21.3 21.9 50 41 43 0.039978687 2.290610043 24 15 0.178092938 10 23 24.1 23.4 50 24 21 0.059928155 3.433630362 16 17 0.019997334 1.145762838 24 24.6 24.1 50 19 19 0 0 16 16 0 0 25 41.3 40.8 50 20 18 0.039978687 2.290610043 37 38 0.019997334 1.145762838 a平均值 0.127450801 7.302393 a’平均值 09.391037257 一圆柱销一菱形销定位：定位元件尺寸分别为10.000mm,9.995mm； 双圆柱销定位：定位元件尺寸分别为9.865mm,10.00