焊接工艺指导书Ⅰ.docVIP

焊接工艺指导书Ⅰ Welding technics instructor I 编制： Making 审核： Auditing 无锡金波隔振科技有限公司 Wuxi Jinbo Gezhen technology Co.,Ltd 二〇一一年三月 March ,2011 1 设备及人员 Equipment and personnel 1.1 设备：纵缝自动氩弧焊机 Equipment : Longitudinal seam automatic argon arc welding machine 1.2 焊接人员须经焊工培训合格后方可上岗操作。 Welder must be approved by a welder training after qualified can mount guard operation 2 焊前准备1 剔出卷边处的毛刺，用细砂纸擦去焊口两边20毫米范围的脏物。To winkle burr of coiling section ,use sand paper to wipe off dirty thing within 20mm for two sides of weld mouth . 2.2 用丙酮洗焊口处的油污，并擦洗夹具紫铜垫槽内的脏物，待丙酮挥发干后即可准备焊接。To use acetone clean oil around weld mouth,and scrub away dirty thing in groove of the clamp copper tray, begin to weld after the acetone has volatilized and dry. 3 焊接型式：纵缝焊对接（自动焊） Longitudinal seam connection auto weld 焊接特性：直流正极性钨极材料：wce20 保护气体：氩气 99.99%记录 做好记录，按波纹管电流电压记录。To record the welding process,refer to the record QR/JB7.5.2-01 of ripple tube current and voltage 焊接电特性表 Weld electricity characteristic list 接头型式Connect type 规格尺寸Specificaiton dimension 材 质填充金属Filled metal （焊丝牌号）焊丝 直径Solder diameter 电流 A电弧电压 V焊接速度Weld speed m/h 钨极 直径Tungsten Diameter 氩气流量（l/min 备注 δ h b A B 0.3 0.3 0 0Cr18Ni9 0Cr18Ni9 / / 15~25 8~10 35~45 φ1 6~8 0Cr18Ni10Ti 0Cr18Ni10Ti 0Cr17Ni12Mo2 0Cr17Ni12Mo2 00Cr17Ni14Mo2 00Cr17Ni14Mo2 0.5 0.3 0 0Cr18Ni9 0Cr18Ni9 25~40 8~12 30~35 0Cr18Ni10Ti 0Cr18Ni10Ti 0Cr17Ni12Mo2 0Cr17Ni12Mo2 00Cr17Ni14Mo2 00Cr17Ni14Mo2 接头型式Connect type 规格尺寸Specificaiton dimension 材 质填充金属Filled metal （焊丝牌号）焊丝 直径Solder diameter 电流 A电弧电压 V焊接速度Weld speed m/h 钨极 直径Tungsten Diameter 氩气流量（l/min 备注 δ h b A B 0.8 0Cr18Ni9 0Cr18Ni9 H0Cr21Ni10 φ0.8 70-90 12-14 35-45 1.6-2 6-8 填充金属可用与焊丝截面积相同的母材代 Filled metal can be replaced by materials Which section area is same to solder 0Cr18Ni10Ti 0Cr18Ni10Ti H0Cr20Ni10Ti 0Cr17Ni12Mo2 0Cr17Ni12Mo2 H0Cr19Ni12Mo2 00Cr17Ni14Mo2 00Cr17Ni14Mo2 H00Cr19Ni12Mo2 1.0 0Cr18Ni9 0Cr18Ni9 H0Cr21Ni10 80-100 0Cr18Ni10Ti 0Cr18Ni10Ti H0Cr20Ni10Ti 0Cr17Ni12Mo2 0Cr17Ni12Mo2 H0Cr19Ni12Mo2 00Cr