多个dsb_c程序.docVIP

bit ds_init() //复位并检测单线器件，返回0，否则死循环{bit flag;uchar i;DQ=0;i=210; while(i) i--; //delay(500); //480DQ=1;i=16; while(i) i--; // delay(40); //15-60while(DQ);flag=DQ;?? //存在器件i=25; while(i) i--; // delay(60); //60-240while(~DQ);i=105; while(i) i--; // delay(420); //(480-60) return flag;} void ds_writebyte(uchar b) //先读写最低位{uchar i,j,temp;for(i=0;i8;i++){?? temp=b0x01;?? b=b1; ?? DQ=0;?? j=2; while(j) j--; //?? delay(2);//1?? if(temp) ?? {??? DQ=1;??? j=25; while(j) j--; //?? delay(60);//15?? }?? else?? {??? j=32;while(j) j--; //??? delay(80); //60??? DQ=1;??? j=5; while(j) j--;//1?? }}} bit ds_readbit(){bit j;uchar k;?? DQ=0;k=2;while(k) k--;//1DQ=1;k=2;while(k) k--;j=DQ;k=25; while(k) k--; // delay(60);return j;} uchar ds_readbyte() //先读的为最低位{uchar i,j,b;b=0;for(i=0;i8;i++){??? j=ds_readbit();?? b=(ji)|b;}return b; } uchar crctest(uchar *p){uchar crc,i,n,cbit,bit0,byte,r;crc=0;for(i=0;i9;i++){byte=*p;?? for(n=0;n8;n++)?? {??? cbit=crc0x01;??? bit0=byte0x01;??? crc=crc1;??? r=cbit^bit0;??? if(r==1) crc=crc^0x8c;??? byte=byte1;?? }?? p++;} //crc==0 校正正确return crc;} void Get_wendu() //得到float型全局量wendu[number_18B20]{uchar code serial_number[4][8]= {0x28,0x2e,0xe0,0xce,0x01,0x00,0x00,0xe6, //一号18b20ROM号??????????? 0x28,0x13,0x2d,0x6c,0x01,0x00,0x00,0x21, //二号??????????? 0x28,0xea,0x07,0x6c,0x01,0x00,0x00,0x80, //三号??????????? 0x28,0x2a,0x0e,0x6c,0x01,0x00,0x00,0xec};//四号????????????? //四个18b20的八字节序列号数据uchar scratch[9]; //TL,TH,ThR,TlR,Con,Res,Res,Res,CRC;//温度高低字节,结构寄存器和卷积码字节uint T_18B20; //整型,合并存储温度数据uchar i,j,crc;char fuhao; //表示正负温度+1,-1; while(ds_init()); //返回1 则继续复位，直到检测到低电平的应答脉冲则向下执行ds_writebyte(0xcc);//SKIP ROM，不发送ROM命令则要发送跳过ROM命令（0xcc)ds_writebyte(0x44);//命令单总线上的所有器件开始转换delayms(10); //一般转换要750us，这里等待3ms足够 for(j=0;jnumber_18B20;j++) //读取转换后的四个温度{?? while(ds_init());??? //返回1 则继续复位，直到检测到低电平的应答脉冲则向下执行 ?? ds_writebyte(0x55); //ROM匹配?? for(i=0;i8;i++) ??? ds_writebyte(serial_number[