壳体零件模具设计 毕业设计.doc

目录 摘要……………………………………………………………………………………2 前言……………………………………………………………………………………4 绪论 5 1 分析研究零件的工艺性 11 1.1零件分析说明 11 1.2工艺方案的确定 11 1.2.1落料工序 13 1.2.2弯曲工序 13 2 模具设计 13 2.1零件工艺分析 13 2.2模具结构设计 13 2.2.1模具结构形式的选择 13 2.2.2模具结构的分析与说明 14 2.2工艺参数计算 15 2.2.1展开尺寸的计算 15 2.2.2 排样尺寸的计算 16 2.2.3冲压力的计算 19 2.2.4压力中心的计算 20 2.2.5落料凸、凹模的刃口尺寸的计算和公差的确定 22 2.2.6凹模周界尺寸计算 26 2.2.7弹性元件的参数计算 27 2.2.8弯曲工序力的计算 27 2.2.9弯曲凸模圆角半径 28 2.2.10弯曲凹模圆角半径 28 2.2.11弯曲凹模的深度 28 2.2.12弯曲凸凹模的间隙 29 2.2.13弯曲凸凹模的尺寸 29 2.3压力机的选择 31 2.4模架的选择及压力机的校核 32 2.5确定装配基准 32 附录 33 英语资料翻译 33 英语资料： 33 中文： 37 毕业设计小结 40 参考文献 41 摘要 冲压制品已在工业，农业，国防和日常生活中的方面得到广泛应用,特别是在机械业中则为突出。机械产品的外壳大部分是冲压制品，产品性能的提高要求高素质的冲压模具和冲压性能，成型工艺和制品的设计。 冲压制品的成型方法很多。其主要用于是冲孔，落料，弯曲，拉伸等。而冲压模，约占成型总数的60%以上。当然如利用电气控制，可实现半自动化或自动化作业。 冷冲冲裁模主要用于金属制品的成型，它是冲压制品生产中十分重要的工艺装置。冲压模的基本组成是：上下模座、下模垫板、下模固定板、凹模镶块、抬料钉、导料板、卸料板,导柱导套、卸料板弹钉、卸料板等。 冲裁模成型的广泛适用，正是我这个设计的根本出发点。 关键词：冲孔、落料 Abstract Stamping products has been extensively applied in the industry, agriculture, national defense and in the daily lives of area, especially in the machinery industry. Mechanical products is the most pressing housing products, and the improvement of product performance requires of high-quality performance stamping molds ,stamping,process and product design. There are many ways of molding products of stamping. Piercing is mainly used for blanking, bending, stretching, etc. And Stamping molds almost form more than 60 percent of the total number. For example ,Electrical Control can be realized as semi-automatic or automatic operation. Cold-metal stamping die mainly used for the molding products, and it is very important in the production of stamping technology devices. The basic component of stamping molds is block model from top to bottom, mould plate, fixed-plate of mould plate, die inserts, raising nails, I. plate , plate unloading I. Introduction sets column, unloading bombs nail plate, plate Discharge and so on. The widely application of blanking moulding is exactly the basic perpose of