轧辊磨床专业术语资料.docVIP

Accompying element:伴生元素 Actual load:有效负载 Accuracy norms:精度标准 AActuating element:执行元件 AAgglomerant cake:烧结块 AIC roll：针状无限冷硬 Air atomization：气压雾化 Anchor tie:锚位杆 Angle probe:斜探头 Anti-crimp roll:防褶辊 Anti-deflection roll :抗挠辊 AAnti spalling property:抗剥落性 Architecture control:框架控制 Arc transition:圆弧过渡 Assessable value:评税值 AAxial:轴向 Auto roll coupling:平顶尖顶持 Babbitt alloy:巴氏合金 BBall screw:滚珠丝杆 BBanded carbide：带状碳化物 Bank mark:滞料纹 Base permeability:原砂透气度 Bar/merchant mill:小型轧机 Bar/merchant steel：条钢 Batching plant:分批配料装置 Batten:用板条固定 Bearing bush:轴瓦 bearing power of ground:地耐力 Bed frame:床身 BBeam blank:异型胚 Beam mill:型钢轧机 Bending discharged design:挠曲度补偿设计 Bearing journal：支撑辊颈 Billet mill:钢胚轧机 Bleeding out rate:漏钢率 Blacking scab：涂料疤 Block gauge：块规 Blank plate:基板、坯板Blooming mill:（方坯）初轧机 Botch milling:铣螺纹槽 Bogie hearth resistance furnace:台式电阻炉 Bore check:精密小测定仪器 Box spanner:内六角扳手；套筒扳手 BBuild-up weld:堆焊 Bus coupler:母线耦合器Burn-on:焊上 Campaign life/length:服役周期 Casting billet:铸坯 Cable drum:电缆盘 Cable trench:电缆沟 CCapillary tube throttle:毛细管节流器 Cardan shaft:万向联辅器 CCc duplexed AIC roll:离心复合无限冷硬轧辊 Cc duplexed SGA roll:离心复合针状球墨轧辊 Cc duplexed SGP roll:离心复合球墨珠光体轧辊 Center quill:中央套管 Centralized lubrication:集中润滑 Chain lubrication:链润滑 Chamfer:倒角 Chatter mark: oscillation mark振纹 CChemical bolt:化学螺栓 Chill crack:激冷裂纹 CChipping:修整表面缺陷 Chip removal:清除碎屑 Chock weight relief system:支顶油缸 Chock tilting device:翻箱机构 Chromium:铬Chuck jaw：卡盘爪 chrome plating:渡铭层 Circumferential speed:线速度 Clamping distance:总长 Coiler pinch rolls:卷取机夹送辊 Cold-redundancy:冷备份冗余 Commbo grinding machine:组合磨床 Commission:试机 Complex contouring:复合曲线 Continuous? tandem mill ：全连续冷轧 Correction grinding and shape correction:修正磨削和辊形修正 Constant infeed velocity:进刀量 Cross screwdriver:十字镙丝刀（Philips screwdriver) Crowning symmetry:中高对称性: Damp structure:阻尼结构 DC arc furnaces：直流电弧炉 Deflector roll:升降辊 De-rating factor:减额因素 Directional valve:导向阀 Dog switch:回参考点减速开关 Down payment:定金 Downtime:停机检查时间；故障检修期间 DDriving dog:传动轧头；传动挡块 Driver:拨盘\拨爪 Double pouring roll