PLC在数控机床中的应用课程.docVIP

习题7 PLC在数控机床中的应用 选择正确的答案? 二?填充,以完成下列各表述? 四. 按要求回答问题或完成作业? 2?机械准停原理示意图如7所示,各信号地址及含义如下: R600.0 MF 译码指令激活条件 R525.0 M19 M19译码信号(主令信号) R569.7 ORT 主轴准停启动 R570.5 ORE 主轴准停结束 R571.5 RST 复位信号 X0.0 LS1 准停释放信号 X0.1 LS2 准停到位信号 R560.0 ORERR 准停有误 R571.1 TM3 延时信号 译码信号地址为F151 3号定时器控制数据地址为D325 试按要求完成机械准停的控制梯形图,如果在5秒内不能完成准停,则发出ORERR信号? 五.读图题? 2?阅读以下梯形图程序,给各段程序作注释? 8?读图题:问: (1)说出润滑系统控制要点; (2)润滑系统运转准备是 行,检测润滑管路堵塞的是 行 (3)说出润滑故障情况及对故障的处理办法? (4)说出4个定时器的作用? (5)中间继电器KA4两端为什么要并联二极管? 1. 机床的冷却系统是这样工作的:按下冷却按钮SB1,输入信号X0.0经过PLC用户程序的处理,输出冷却启动信号Y86.5,控制中间继电器KA1的线圈,进而由KA1的触点进一步接通控制冷却接触器KM1的线圈,接触器KM1的主触点吸合,使冷却电机M1转动,带动水泵工作,冷却液喷出? 试画出包括I/O接口电路的电气工作原理图? 试画出冷却控制的PLC梯形图? 4. 画出TK7640主轴控制电路图? 2. 在图1主轴定向控制梯形图中,根据机床控制要求,在机床操作面板上增设主轴定向按钮?该按钮在手动工作方式(地址R557.7)下生效,按钮地址为X2.7?问: 怎样对图1的主轴定向控制梯形图进行改进? Acknowledgments The authors would like to thank Johns Hopkins University for the TC-1 cells. This work was supported by a National Health Research Institutes intramural grant (IV-103-PP-22) and grants from the National Science Council, which were awarded to Y.C. Song (NSC 99-2321-B-400-004-MY3) and S.J. Liu (NSC 103-2321-B-400-008). Author Contributions Y.C.S. and S.J.L. designed the studies. Y.C.S. performed the research and analyzed the data. Y.C.S. and S.J.L. wrote the manuscript. Additional Information C57BL/6 mice were immunized subcutaneously (s.c.) once with 1 μ g of peptide mixed with or without 10 μ g of CpG adjuvant. After one week, splenocytes were harvested, and the response of IFN-γ -secreting cells was determined by ELISPOT after 48 h of peptide stimulation. Briefly, 2 × 105 splenocytes were incubated with 1 μ g/ml irrelevant peptide or RAH peptide in an anti-IFN-γ -coated polyvinylidene fluoride (PVDF) plate for 48 h. After incubation, the cells were removed, and a biotinylated anti-IFN-γ Ab (eBioscience, San Diego, CA, USA) was added to each well. The plates were incubated at 37 °C for 2 h. Following the addition of the avidin-HRP reagent (eBiosci