机械制图螺纹画法课程.docVIP

机械制 2007-03-28 14:13 螺纹的规定画法??1.外螺 国标规定,螺(大)及螺,牙底(小)用,在平行于螺杆,螺杆的倒角或倒;在垂直于螺,表示牙底的3/4圆,此,如12-5? 图12-5 ??2.内螺纹图12-6是[图13-6(a)],牙底(大)为细实线,牙(小)及螺[图13-6(b)],牙底,牙底仍然3/4圈的,并图12-6 ?? 绘制不穿通的螺孔时,一般,如12-7(a)?当需要表示螺纹收尾时,螺30o的,如12-7(b)?图12-7(c)表示出螺图12-7 3.内?外螺纹连接的画法如12-8表示,在剖,其旋合部分,非旋合部分仍按各自的图12-8 螺???4.非画非标准牙型的螺,应画出螺纹牙型,并,如12-9? 图12-9 螺纹的规定标注各种螺,为了便于区别,还必须在图形上进行标注? (1) 普通螺??? 标注内容为: 特征代 公×螺距 旋向 — 中 — 旋合度代 其中:特征代 M 单线粗牙螺纹只标公称直径,单线细牙螺纹标公称直径×螺距?????旋向:分,右旋不,左旋用LH表示 螺:由表示公差等,如:6H6g(内螺纹用大写字母,外螺)?如果中径与顶径公差带代号相同,则只注一个代号,如:7h;如果螺,则分别标注,如:5g6g 旋合:螺(S)?中(N)?长(L)三种,中旋合,特殊需要,如M10-6g-40 普通螺,尺寸界普通螺 (2) 管螺??? 标注内容为: 特征代 公 公差等 ?? 其中:特征代 G Rc在注方法是用一,一端指向螺,另一端引一,将螺纹标记写在横线上侧,标注示例如图?管螺(3) 梯形螺: 特征代 公×导程(P螺距) 旋向 其中:特征代 Tr???? 单线螺纹只标公称直径,多×导程(P螺距),如 Tr 40X14(P7)?????旋向同普通螺 梯形螺 梯形螺锯齿形螺纹标注示例?? (4) 锯齿形螺纹的标注 标注内容为: 锯齿形螺纹标注内容及在图上的标注方法与梯形螺纹相同,如 特征代 公×导程(P螺距) 旋向 其中:特征代 B单线螺纹只标公称直径,多×导程(P螺距),如 Tr 40X14(P7)?????旋向同普通螺 (5) 非 非,还需要标出中径?顶径的极限尺寸,见图7-9所示“特”字 Acknowledgments The authors would like to thank Johns Hopkins University for the TC-1 cells. This work was supported by a National Health Research Institutes intramural grant (IV-103-PP-22) and grants from the National Science Council, which were awarded to Y.C. Song (NSC 99-2321-B-400-004-MY3) and S.J. Liu (NSC 103-2321-B-400-008). Author Contributions Y.C.S. and S.J.L. designed the studies. Y.C.S. performed the research and analyzed the data. Y.C.S. and S.J.L. wrote the manuscript. Additional Information C57BL/6 mice were immunized subcutaneously (s.c.) once with 1 μ g of peptide mixed with or without 10 μ g of CpG adjuvant. After one week, splenocytes were harvested, and the response of IFN-γ -secreting cells was determined by ELISPOT after 48 h of peptide stimulation. Briefly, 2 × 105 splenocytes were incubated with 1 μ g/ml irrelevant peptide or RAH peptide in an anti-IFN-γ -coated polyvinylidene fluoride (PVDF) plate for 48 h. After incubation, the cells were removed, and a biotinylated anti-I