毕业设计(完整内容)米跨轻型门式刚架结构厂房计算书分析.docVIP

泉州市华力钢结构公司3#厂房设计 [摘要] 本工程为泉州市华力钢结构公司3#厂房设计。通过查阅有关图集及相关教材，将门式刚架厂房设计为单跨双坡跨，柱距为6.6m，跨度为30m,总的建筑面积为1584m2。 该单层门式刚架结构是以轻型焊接H型钢（变截面）作为主要承重骨架，用冷弯薄壁型钢（C型）做檩条、墙梁；以0.5mm厚压型钢板做屋面、墙面；采用75mm玻璃棉作为保温隔热材料并适当设置支撑的一种轻型房屋结构体系。 根据已形成的建筑图及其相关要求，对每榀刚架的最不利荷载进行计算，使用PKPM软件完成刚架的合理截面计算，然后通过设计规范的相关要求，对刚梁、柱、支撑、檩条等构件进行强度、刚度，稳定性等验算，用CAD分别绘制出设计图。最后，整理计算书并出图。 [关键词] 轻型门式刚架 钢结构 设计 Quanzhou huali heavy loader workshop 3 # workshop design [abstract] the project for quanzhou huali heavy loader workshop 3 # workshop design. By looking at the atlas and relevant material, door frame factory building design for single across different dual slope, column distance of 6.6 m, span of 30 m, the total construction area of 1584 m2. The single type of door rigid frame structure with light welding h-beam (variable cross-section) as the main load-bearing skeleton, with cold-formed thin-walled steel purlin, (C) do wall beam; With 0.5 mm thick do steel sheet roof, walls; Using 75 mm glass wool as thermal insulation material and properly set up to support a lightweight building structure system. According to the construction diagram and related requirements of already formed, for every nature, the most unfavorable load calculation of the frame, using PKPM software to complete the reasonable cross section calculation of frame, and then through the design specification, the requirements of the relevant on beam, column, supports, purlin artifacts such as strength, stiffness, stability calculation, map out separately with the CAD design. Finally, calculation and drawing. [key words] Light portal rigid frame，The steel structure ，design 目录 第一章 工程概况 1 1.1工程地质勘探资料 1 1.2气候条件 1 1.3荷载取值 1 1.4结构的安全等级 1 1.5建筑用材 1 第二章 结构选型 2 第三章 荷载计算 3 3.1荷载标准值 3 3.1.1永久荷载标准值 3 3.1.3风荷载 3 3.2荷载组合 4 3.2.1由永久荷载控制的组合 4 3.2.2由可变荷载控制的组合 4 第四章 内力分析 5 4.1 PKPM电算信息 5 4.2 PKPM电算结果 6 4.3内力包络图 7 第五章 钢架截面设计 8 5.1截面选择 8 5.2钢架柱验算 9 5.2.1宽厚比限值 9 5.2.2钢架柱腹板有效宽度计算 9 5.2.3钢架柱刚度验算 10 5.2.4钢架柱的强度验算 11 5.2.5稳定性验算 11 5.3钢架梁验算 12 5.3.1 B2点所在截面 12 5.3.2 C点所在截面 14 5.3