结构设计工艺规范--钣金(超经典,知名企业资深工艺工程师编写)课程.docVIP

[键入文字] [键入文字] 钣金设计工艺规范 目录 TOC \o 1-3 \h \z \u   HYPERLINK \l _Toc434797596 钣金设计工艺规范  PAGEREF _Toc434797596 \h 1  HYPERLINK \l _Toc434797597 目录  PAGEREF _Toc434797597 \h 2  HYPERLINK \l _Toc434797598 1. 目的  PAGEREF _Toc434797598 \h 4  HYPERLINK \l _Toc434797599 2. 适用范围  PAGEREF _Toc434797599 \h 4  HYPERLINK \l _Toc434797600 3. 规范内容  PAGEREF _Toc434797600 \h 4  HYPERLINK \l _Toc434797601 3.1 公司常用板材规格汇总  PAGEREF _Toc434797601 \h 4  HYPERLINK \l _Toc434797602 3.1.1常用板材和工艺影响  PAGEREF _Toc434797602 \h 4  HYPERLINK \l _Toc434797603 3.1.2选用原则  PAGEREF _Toc434797603 \h 5  HYPERLINK \l _Toc434797604 3.2 冲裁  PAGEREF _Toc434797604 \h 5  HYPERLINK \l _Toc434797605 3.2.1毛刺  PAGEREF _Toc434797605 \h 5  HYPERLINK \l _Toc434797606 3.2.2公差  PAGEREF _Toc434797606 \h 5  HYPERLINK \l _Toc434797607 3.2.2.1冲裁线性尺寸公差  PAGEREF _Toc434797607 \h 6  HYPERLINK \l _Toc434797608 3.2.2.2成型尺寸公差  PAGEREF _Toc434797608 \h 6  HYPERLINK \l _Toc434797609 3.2.2.3经弯曲成形而形成冲压件的角度尺寸  PAGEREF _Toc434797609 \h 7  HYPERLINK \l _Toc434797610 3.2.2.4经冲孔、落料及其他分离工序加工而成冲压件圆角半径的线性尺寸  PAGEREF _Toc434797610 \h 8  HYPERLINK \l _Toc434797611 3.2.2.5在平板或成形件平面处，经冲裁加工而成的角度尺寸  PAGEREF _Toc434797611 \h 8  HYPERLINK \l _Toc434797612 3.2.2.7 直线度、平面度未注公差  PAGEREF _Toc434797612 \h 8  HYPERLINK \l _Toc434797613 3.2.3 冲裁孔位设计尺寸基准基本原则  PAGEREF _Toc434797613 \h 9  HYPERLINK \l _Toc434797614 3.2.4 冲裁的结构工艺性  PAGEREF _Toc434797614 \h 9  HYPERLINK \l _Toc434797615 3.2.4.1冲裁件的外形及内孔  PAGEREF _Toc434797615 \h 9  HYPERLINK \l _Toc434797616 3.2.4.2冲裁件的悬臂与狭槽。  PAGEREF _Toc434797616 \h 9  HYPERLINK \l _Toc434797617 3.2.4.3 冲孔最小尺寸要求  PAGEREF _Toc434797617 \h 9  HYPERLINK \l _Toc434797618 3.2.4.4 冲裁的孔间距与孔边距  PAGEREF _Toc434797618 \h 10  HYPERLINK \l _Toc434797619 3.2.5数冲冲孔与鐳射切割及冷冲模工艺区别  PAGEREF _Toc434797619 \h 10  HYPERLINK \l _Toc434797620 3.2.6公司常用冲孔尺寸  PAGEREF _Toc434797620 \h 11  HYPERLINK \l