- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
项目改造施工方案(英文版) 2
糖厂1×45t/h CFB锅炉改造方案
The Upgrade Project of 1×45 t/h CFB Boiler
一 工程概况:
1. Project Overview
本项目为一台1×45t/h CFB锅炉改造,其主要工程项目为:更换二次风机,引风机;对锅炉二次风管部分管道进行改造,增加二次风管风门调节阀,送料风调节阀,密封风调节阀,圆形碳钢给料管改为方形不锈钢给料管,螺旋给料机检查门改为快开式;
This project is a renovation of 1 × 45t/h CFB boiler, and its main projects are as follows: to replace the secondary fan and induced-draft fan; to transform partial pipeline of boiler secondary air duct, to increase the throttle valve of secondary air duct, throttling valve of both the feeding airflow and the sealing airflow, to change the feeding pipe from round carbon-steel into square stainless and to change the inspection door of spiral feeder into quick-opening type.
100t/h大气热力式除氧器钢架与平台制作,安装一台100t/h大气热力式除氧器和一台?800连续排污器,增加锅筒连续排污装置;安装取样器4个,
Fabrication of steel frame of 100 t/h atmospheric thermal deaerator and its platform; installation of a 100t / h atmospheric thermal deaerator and a ?800 continuous blowdown device; increase of continuous blowdown device for boiler drum; and installation of four samplers.
受煤斗加高700mm左右,安装振动给料机一台,更换破碎机一台,安装皮带秤一套。
Increase the height of coal-receiving hopper by around 700mm, install a set of vibrating feeder, change a set of crusher and install a set of belt scale.
锅炉电气控制系统:控制系统改为PLC控制;给水泵、一次风机、二次风机、引风机改为ABB变频控制,增加部分控制电缆和桥架。
Electrical control system of boiler: change the control system to the PLC control; change feed pump, primary fan, secondary air fan, induced-draft fan to ABB variable frequency control, increase some control cable and cable tray.
施工方案
2. Construction Scheme
1).引风机更换,拆除原有引风机,利用原有引风机基础,新引风机轴承座和电机仍坐在一基础上,风机壳在原基础上焊接400mm高的钢支架固定,固定后为美观浇筑混凝土。根据风机安装高度和风机出口尺寸,做天园地方大小头与原风道连接。按风机安装技术要求精度找平找正。
1). Replace induced-draft fan and remove the previous induced-draft fan; the bearing block of new induced-draft fan and the motor are still on the same foundation, for which the original induced-draft fan foundation will be used; weld a 400mm-high steel bracket to fix the draught fan casing on the original fou
文档评论(0)