Operating Procedure for Temperature Uniformity Survey of 50t Aging Furnace.doc

50吨时效炉炉温均匀性测试操作规程 Operating Procedure for Temperature Uniformity Survey of 50t Aging Furnace Q/SWA JH02A.15-2011 1 范围： 1. Scope 1.1 本规程规定了50吨时效炉的炉温均匀性测试操作要求。 1.1 This procedure stipulates requirements for the temperature uniformity survey of 50t ageing furnace. 1.2 本规定适应于50吨时效炉的炉温均匀性测试工作。 1.2 This procedure applies to operations of the temperature uniformity survey of 50t aging furnace. 1.3 本规程根据AMS 2750D制定。 1.3 The procedure is established according to AMS 2750D. 2 要求 2. Requirements 2.1 热处理设备及要求 2.1 Heat Treatment Equipment and Requirements 2.1.1 设备代码：02 Sxl 50 2.1.1 Equipment Code: 02 Sxl 50 2.1.2 50吨时效炉符合AMS2750D中规定的Ⅱ级炉及D类仪器 2.1.2 50t aging furnace conforms with class 2 furnace and class D instruments in AMS2750D. 2.1.3 炉膛尺寸：17000×4500×2000mm(长×宽×高) 2.3.1 The chamber size of the furnace: 17000×4500×2000mm(L×W×H) 2.1.4 有效工作区尺寸：16000×4000×1600mm(长×宽×高) 2.1.4 The ffective working zonr size: 16000×4000×1600mm(L×W×H) 2.1.5 有效工作区分区：六区（1，2，3，4，5，6区） 2.1.5 Effective working zones of the furnace: 6 zones (zone No. 1,2,3,4 ,5 and 6) 2.1.6 工作温度：110-220℃ 2.1.6 Working temperature: 110-220℃. 2.1.7 炉温均匀性要求：±5℃（±10℉） 2.1.7 Requirement for temperature uniformity in the furnace: ±5℃（±10） 2.2 Frequency of the temperature uniformity survey of the furnace 2.2.1 定期测试： 2.2.12.2.1.1 炉温均匀性定期测试周期为一月，测试时间间隔到期后允许延长3天。emperature uniformity test is periodically conducted for one (1) month during normal production with three (3) days extending after expiration of the interval. 2.2.1.2 如果AMS2750D要求连续8次测试，则测试可。2.2.1.2 If the results of contuuous 8 times of survey are acceptable according to the relevant requirements of AMS 2750D, the test interval can be extended for two months. 2.2.2 初次测试：2.2.2.1 参考AMS2750D 3.5.3和3.5.4条，确认炉子调整、改型或维修炉子温度均匀特性了改变时，必须进行初次测。2.2.2.2 如果某次测试结果不合格，则下次执行初次测测试周期复到每月一次直至达到测试周期延长条件时止。2.3.1 Test mode: empty furnamce, support-type, volume measuring method 2.3.2 测试传感器准备： 2.3.2 Preparation of test sensor 2.3.2.1 测试传感器：符合表1要求 2.3.