数码管显示时间及点阵显示字符.docVIP

//数码管显示时间及点阵显示字符 #include reg52.h #include intrins.h #define uchar unsigned char #define uint unsigned int //定义Max7219端口 #define DUAN P0 //P0口控制段 #define WEI P2 //P2口控制位 sbit k_hour=P1^0; // 更改小时按键 sbit k_min=P1^1; // 更改分钟按键 sbit k_sec=P1^2; // 更改秒按键 //定义数码管端口 sbit Max7219_pinCLK = P1^2; sbit Max7219_pinCS = P1^1; sbit Max7219_pinDIN = P1^0; //Max7219位定义 unsigned char key; //P3按键扫描(执行模块控制) code uchar seg7code[11]={ 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0XBF }; //显示段码 数码管字跟 uchar wei[8]={0XFE,0XFD,0XFB,0XF7,0XEf,0XDf,0XBf,0X7f}; //位的控制端 uchar numb[8]; //定义字符串 uint sec=0,min,hour; //数码管初始定义 uchar code disp2[7][8]={ {0x00,0x3E,0x2A,0xFF,0xAA,0xBE,0xC0,0x00}, //电 {0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x00}, //一 {0x00,0x00,0x1E,0x20,0x40,0x20,0x1E,0x00}, //V {0x00,0x00,0x4E,0x4A,0x4A,0x7A,0x00,0x00}, //5 {0x00,0x00,0x42,0x7E,0x42,0x00,0x00,0x00}, //I {0x00,0x0C,0x1E,0x3C,0x3C,0x1E,0x0C,0x00}, //love {0x00,0x00,0x3E,0x40,0x40,0x3E,0x00,0x00}, //U }; char flag; //定义点阵显示字符 void Delay_xms(uint x) { uint i,j; for(i=0;ix;i++) for(j=0;j300;j++); } //公用的延时程序 //功能：向MAX7219(U3)写入字节 //入口参数：DATA //出口参数：无 void Write_Max7219_byte(uchar DATA) { uchar i; Max7219_pinCS=0; for(i=8;i=1;i--) { Max7219_pinCLK=0; Max7219_pinDIN=DATA0x80; DATA=DATA1; if(flag)Delay_xms(500); Max7219_pinCLK=1; } } //功能：向MAX7219写入数据 //入口参数：address、dat //出口参数：无 //说明： void Write_Max7219(uchar address,uchar dat) { Max7219_pinCS=0; Write_Max7219_byte(address); //写入地址，即数码管编号 Write_Max7219_byte(dat); //写入数据，即数码管显示数字 Max7219_pinCS=1; } void Init_MAX7219(void) { Write_Max7219(0x09, 0x00); //译码方式：BCD码 Write_Max7219(0x0a, 0x03); //亮度 Write_Max7219(0x0b, 0x07); //扫描界限；8个数码管显示 Write_Max7219(0x0c, 0x01); //掉电模式：0，普通模式：1 Write_Max7219(0x0f, 0x00); /