bartendr软件打印条码标签实验.docVIP

  • 11
  • 0
  • 约8.24千字
  • 约 6页
  • 2016-10-05 发布于贵州
  • 举报
bartendr软件打印条码标签实验

西 南 财 经 大 学 天 府 学 院 物流自动化识别技术 之 实验报告 (2009届本科) 学 院 西南财经大学天府学院 专 业 物 流 管 理 班 级 2009级物流1班 指导老师 何 亮 老 师 姓 名 张 思 思 学 号 实验目的:熟练运用Bartender 7.75软件,打印出条码标签 实验内容和步骤 安装Bartender 7.75软件 选择安装文件夹,并打开,双击SETUP.EXE(如图:),开始安装程序; 选择自己要用的语言(如图所示:),确认后开始进入安装程序; 点击“完成”,完成安装; 条码标签制作 店内码 步骤一:点击新建标签,进入界面; 步骤二 :点击工具栏上按钮,可画出线条,调整标签布局; 步骤三:编辑文本,点击工具按钮,点击标签区域,即出现字样,双击字样,把屏幕数据内容改为“品名:”“沙田柚子”等字样,并调整字体; 步骤四:添加条码,点击工具栏上条码编辑工具,移动到标签设计区域,鼠标左键点击设计区域,便出现如下的默认条码,双击后将屏幕数据改为沙田柚子的店内条码 ,将条形码的符号体系选择为EAN/UCC-13码,如图所示: 步骤五:插入超市LOGO,点击默认对象下拉菜单,双击“图片”, ,即出现图样,双击该图样,然后点击“选择图片” 插入图片完成; 步骤五:完成以上全部步骤后,导出图片(如图); 物流条码 步骤一:点击新建标签,进入界面; 步骤二 :点击工具栏上按钮,可画出线条,调整标签布局; 步骤三:编辑文本,点击工具按钮,点击标签区域,即出现字样,双击字样,把屏幕数据内容改为“品名:”“FROM”“TO”等字样,并调整字体; 步骤四:添加条码,点击工具栏上条码编辑工具,移动到标签设计区域,鼠标左键点击设计区域,便出现如下的默认条码,双击后将屏幕数据改为物流条码 ,将条形码的符号体系选择为EAN/UCC-128码,如图所示: 步骤五:完成以上全部步骤后,导出图片: of support and hanger. Cable hole plugging gaps should use qualified fireproof materials, block surface should have sufficient strength, surface appearance. When cables pass through the firewall, of lax structure of local fire safety clamps. Thermoplastics production, to comply with the process, no bubbles in the thermoplastics pipes, linear nose consistent with the core wire specifications, contact is good, no cracks, break. Tinned copper nose clean solder full exterior surface is smooth without burrs. Control cable Assembly should be fastened, dense, solid, clean, and beautiful. Secondary wiring the cable terminations should be arranged by the actual location of the device line cards, the wiring from the upper to the lower, from left to right in the order. Fixed to maintain consistent spacing between lines, flat, should be around the corner in the same location, same shape, to ensure that the wiring process neater and more elegant. 5 thermal process control measures for quality problems 5.1 control thermal duct system leakage measure to ensure t

文档评论(0)

1亿VIP精品文档

相关文档