100t焊接滚轮架设计总体设计和从动滚轮座设计毕业设计整理初稿.docVIP

摘要 焊接与铸造,成为机械制造业的主要加工方法,许多传统的铸锻产品,也由焊接制品或铸—焊焊接结构生产的整个过程同其他任何一生产过程一样,除了基本的生产工序以外,还包括大量的辅助工序,其中主要是焊接零件的制备,主动轮上的功率除以传动效率从而算出需要的电机功率,从而选择电动机,再将电动机的转速进行分配算出减速器?涡轮蜗杆? 关键词: 焊接;生产工艺质量;焊接滚轮架;筒形工件 Abstract Welding and casting, forging, machining, heat treatment and other metalprocessing technology portfolio and become the main processing machinery manufacturing methods, the Casting and Forging in many traditional products, but also by the welding or casting products - welding, forging - replaced by welding products. Welded structure with the entire process of production of any other as a production process, in addition to the basic production processes, but also including a large number of auxiliary procedures, which are mainly parts of the preparation of welding, assembly, delivery and inter-process products such as variable bit with the clean-up . Load is calculated through the shaft, bearings, couplings, such as the specific size, and check them. The initial stage of the distribution of the transmission ratio, active power divided by the number of launches in order to calculate the transmission efficiency of the electric power needs in order to select the motor, and then carry out the distribution of motor speed reducercalculated, turbine worm. Key words: welding; production process quality; welding wheel frame; cylindrical workpiece 目录 摘要 ..I Abstract II 目录 Ⅲ 前言 1 第1章 绪论 2 1.1焊接工艺概述 21.2 工艺装备与生产的工艺的关系 2 1.3 焊接工艺装备 5 第2章 滚轮架概述 9 2.1 滚轮架分类 9 2.2 中心角与驱动力?支反力的关系 9 2.3滚轮驱动方案 10 第3章 滚轮架的设计与校核 13 3.1 电动机的选择 13 3.2 从动轮的设计 14 3.3 圆柱蜗杆的设计 18 结论 22 参考文献 23 致谢 24 附件1 25 附件2 39 前言 随着现代工业的高速发展和焊接技术的不断进步,焊接作为一种金属连接的工艺方法,在金属结构生产中已经基本取代了铆接连接工艺,成为机械制造业的主要加工方法,许多传统的铸锻产品,也由焊接制品或铸—焊早期的焊接结构大多数是用手工电弧焊完成的,有时还用到氧—乙炔气焊,焊接结构生产也已向机械化,现在不仅已经制成了各种机械化,而且还制造了大量的焊接辅助装备,焊接结构生产流水线和生产自动线早已成为现实器人在某些部门得到了较普遍的使用,焊接机器人比其他类型机器人应用更广泛,不仅可以提高焊接结构的生产率,降低产品成本,提高产品质量,同时也使生产工人的健康进一步得懂到保障,环境污染也有所下降,由于焊接结构的多样化及生产过程的复杂性,目前国内焊接生产的机械化,手工操作在某些产品,甚至某些行业中仍占较大的比例第1章 绪论1.1 焊接工艺