喷码机多米诺操作2复件附件2：标准模版.pptVIP

第一单元: 一、 1,耗材规格,严禁与其他型号的耗材混用 2．喷头，和机身，在移动时要轻拿轻放，避免磕碰，安装位置要稳定，避开震源，防止震动，喷头部位很脆弱，严禁磕碰。机器要固定在底座上，防止喷码机从高处坠落到地面。造成严重损坏，喉管严禁挤压弯折 3.每天开机前要检查清洗喷头，充分干燥后才能开机，清洗剂不可用其他液体代替。 第二单元: 第四单元: 一. 一. 二. 报充电槽上有墨水应当从新关机在做一个喷头清洗，清洗后最重要的是把充电槽中间缝隙的清洗液吹掉，一般风干或自然晾干缝隙中的清洗液是不会掉的。 伊利，为梦想创造可能！ 打印延时、改变字高、字宽 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 打印延时 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 设置字高 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 设置字宽 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 设置字宽 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 单元回顾 讲点1：当码打的过早时未打印到指定位置调节打印延时。 讲点2：打印高度是不能随便调节的。 重点与难点：打印高度可以随便调节吗？ Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 课程目录 第一单元：注意事项 第二单元：开机和关机 第三单元：喷码尺寸调整和相关设置 第四单元：故障诊断 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 一、当打印延时数值调整到最大或最小时打码位置还是不能改变应当怎么办。 二、报充电槽上有墨水该怎么办。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 总体课程回顾 总结1：掌握知识 总结2：灵活运用 总结3:善于总结，分析，记录。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 液态奶事业部喷码机课程系列 多米诺A系列喷码机操作