《健骑机虚拟样机的建立与仿真分析》.doc

本科毕业论文（设计）论文题目： 健骑机虚拟样机的建立与仿真分析学生姓名： 所在院系： 机电学院所学专业： 机械设计制造及其自动化导师姓名： 完成时间：摘 要健骑机是一种作用于腿部及胸部肌群，可使全身80%的肌肉和关节同时参加运动的一种不可多得的健身器材。本文以学院东操场边的健骑机实物为参考，在研究分析健骑机的组成和各零件间的相互关系的基础上，测量其各零件的数据。首先利用Pro/E建模功能对各零件进行建模；然后利用Pro/E的装配模块，通过定义“驱动”，完成了快速成型机的运动仿真，并在此基础上进行干涉分析，经过干涉分析找出问题，再回到三维模型中去完善模型，最终生成满足设计要求的健骑机模型，为其结构动态优化设计提供参考。关键词：健骑机，Pro/E，建模AbstractCycling equipment acting on the leg and chest muscle, is a rare equipment that enable 80% of the whole body’s muscles and joints to move at the same time. In this paper, study on the composition of the cycling equipment parts and analysis of the specific relationship between the various parts have been carried out according to the cycling equipment at the east of the colleges playground; the data of its every part measured as well. First of all , the paper has builded the model using Pro/E modeling capabilities. Then, through defining the ’driver’ and using the Pro/E assembly module software, it has completed the motion simulation. On the basis of interference analysis, the problems were identified and the model was improved. Finally, the paper has developed a model which can meet the design requirement and make a reference for its optimal dynamic design.Key words: Cycling Equipment, Pro/Engineer, Modeling目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc256000001 1 绪论狷濯迄绸淦音答钽荼冂契跸迸 PAGEREF _Toc256000001 \h 4 HYPERLINK \l _Toc256000002 1.1 课题背景及研究意义捻如颊支暴乍度亟绗黄蛔吉硇 PAGEREF _Toc256000002 \h 4 HYPERLINK \l _Toc256000003 1.2 健身器材的研究现状汪心镜哨微龉腐范涡睃杀姐遇 PAGEREF _Toc256000003 \h 4 HYPERLINK \l _Toc256000004 1.1.1 健身器材的发展与品牌化缧痢缯浙闯鲺删雹悭啸瑷铰咴 PAGEREF _Toc256000004 \h 4 HYPERLINK \l _Toc256000005 1.1.2 健身器材的分类与功能罩辨寺岿盍腽惶恳鸽绔柏椿脚 PAGEREF _Toc256000005 \h 5 HYPERLINK \l _Toc256000006 1.3 现代机械设计方法概述獗训铫鹚诌蟀高烧骸菲栖验近 PAGEREF _Toc256000006 \h 6 HYPERLINK \l _Toc256000007 1.4 本文主要研究内容忏梆建秆鹌颁叠遽尔萼刎很厦 PAGEREF _Toc256000007 \h 7 HYPERLINK \l _Toc256000008 2 Pro/E的功能概述唠绍砥傀溆泌啭獬概疃痧辆恳 PAGEREF _Toc256000008 \h 8 HYPERLINK \l _Toc256000009 2.1 Pro/E的三维模型创建功能冲搿抒源瑕氮妆芹北花匾眚王