大学毕设论文--三辊卷板机.docVIP

三辊卷板机设计 摘 要 关键词: Three Roller Bending Machine Design Abstract This design is about the three-roller symmwtry rolling machine,mainly calcats the up and down roller and the decelerator During the front process of the design,the rolling machine`s structucre design and the analysis of strength are described. The rolling machine` structure is three-roller symmetry. Pressure provides pressure under owing structure the above-average roller , the roller does revolution sport under two , sheet material provides moment of torsion to roll of system.It has a series of advantages such as simply structure,small volume,light weight,economical and so on.YZ type YZ-160L-6 motor is selected as the power source,which adapts situation such as slience quenching and light reverse velocity. The last part of the paper is ahout decelerator which is choosing triple expanding columm gear constiuction .The material of gear is 40Cr which has been hardening surface.The gears, axes, keys, bearings are checked, so to confirm this design is practical Key words: Rolling machine；Motor；Decelerator；Key；Gear 目 录 1绪 论 1 1.1 概述 1 1.2 卷板机的发展趋势 3 2般小型卷板机结构及特点分析 4 2.1 辊卷板机 4 2.2 三辊卷板机 5 2.2.1 对称式三棍卷板机结构及特点 5 2.2.2 不对称三辊卷板机特点 5 2.3 方案的确定 6 3 传动设计 7 3.1 传动方案的分析及确定 7 3.2 主传动系统的确定 8 3.2.1 8 4 动力设计 9 4.1 主电机的选择和计算 9 4.1.1 9 4.1.2 主电机的功率确定 10 4.2 上辊的设计计算校核 20 4.2.1 20 4.2.2 刚度校核 20 4.2.3 上辊强度校核 21 4.2.4 疲劳强度安全强度校核 21 4.2.5 上辊在卸料时的校核 22 4.3 下辊设计计算及校核 23 4.3.1 23 4.3.2 下辊刚度校核 24 4.3.3 下辊弯曲强度校核 24 4.3.4 下辊疲劳强度校核 25 5 减速器的设计计算 28 5.1 传动方案的分析和确定 28 5.2 减速器传动装置总的传动比和各级传动比的分配 28 5.2.1 28 5.3 传动装置各轴的参数计算 29 5.3.1 29 5.3.2 各轴功率 29 5.3.3 各轴转矩 29 5.4 齿轮传动设计 30 5.4.1 30 5.4.2 第二级传动设计 34 5.4.3 第三级传动设计 37 5.5 蜗轮、蜗杆的传动设计 40 5.5.1 40 5.5.2 参数的设计 40 5.6 轴的设计校核计算 42 5.6.1 42 5.6.2 轴的校核计算 43 5.7 轴承校核 47 5.7.1 47 5.7.2 求轴承受到的径向力 48 5.7.3 验算轴承寿命 48 5.8 键的校核 48 6 设备的维护、润滑与维修 50 7 设计可行性分析 51 7.1 设备的经济性分析 52 7.1.1