国外大学定向井.pptVIP

下载本文档

5
0
约4.68千字
约 36页
2016-12-17 发布于重庆
举报
版权申诉

国外大学定向井.ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

* Example 8.10 Design a kickoff for the wellbore in Fig. 8.35. From Ouija Board, b = 5.8o, g = 97o e = S48W = 228o eN = N53W = 307o a = 2o L = 150 ft aN = 6o De = 79o Find b, g and d * Fig. 8.36: Solution for Example 8.10. Where to Set the Tool Face High Side Present Direction High Side New Direction b = 5.8o g = 97o * Dogleg Severity From Equation 8.43 the dogleg severity, * Fig. 8.36: Solution for Example 8.10. 307o With jetting bit: 325o 345o 228o qM = 20o * Fig. 8.36: Solution for Example 8.10. Where to Set the Tool Face High Side Present Direction New Direction Tool Face Setting Compensating for Reverse Torque of the Motor High Side * * * * * * * * * * * * * * Petroleum Engineering 406 Lesson 20 Directional Drilling (continued) * Lesson 17 - Directional Drilling cont’d Tool-Face Angle Ouija Board Dogleg Severity Reverse Torque of Mud Motor Examples * Homework: READ: Applied Drilling Engineering”, Chapter 8 (to page 375) * Fig. 8. 30: Graphical Ouija Analysis. Solution Tool Face (g) * Fig. 8. 30: Graphical Ouija Analysis. Solution Tool Face (g) Initial Inclination = 16o GIVEN: a = 16o De = 12o aN = 12o g = ? o b = ? o New Inclination - 12o De = 12o Over one drilled interval (bit run) * Fig. 8.33 Basis of chart construction is a trigonometric relationship illustrated by two intersecting planes b b = dogleg angle a De aN * Problem 1 Determine the new direction (eN) for a whipstock set at 705 m with a tool-face setting of 450 degrees right of high side for a course length of 10 m. The inclination is 70 and the direction is N15W. The curve of the whipstock will cause a total angle change of 30/30 m. * Problem 1 a = 7o (inclination) e = 345o (azimuth) g = 45o (tool face angle) L = 10 m (course length) d = 3o/ 30 m (dogleg severity) eN = ? o g = 45o * Solution to Problem 1, part 1 I. Use Equation 8.43 to calculate . The dogleg s