《通用技术7.2.2工艺(木工).pptVIP

第二节 工艺 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 划出基准线——划加工尺寸线——划轮廓线——冲眼 1.划线 金属材料的加工工艺 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. C. D. A． B. 1.用一个等边角钢制作如图所示的直角型支撑架，下列四种划线（细实线表示划线，按划线锯割）中，最合理的是（ ） A Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2. 锯割 (1)锯条的正确安装 (2)锯割操作要领： (3)起锯方法： Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2．王凯同学用角钢制作直角三角架时，经过划线（如图甲所示）、锯割、弯曲等操作后，发现角钢转角处间隙过大（如图乙所示）。造成这种后果的原因可能是 A.划线交点没到边界线 B.两条划线的角度小于90° C.锯割时锯偏了 D.角钢弯曲没到位 C Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2.锯割一根直径为3cm的合金钢管，应该选用的手锯是（ ） C A D B C Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. A D B C 3.如图所示是四位同学在用手锯锯割铁棒的场景，其中操作符合规范的是 D Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.如右图所示是正常锯割时左右手的握法，其中右手的作用是用力推与拉，左手的作用是（ ） A.推与拉都不用力 B.适时向下用力，并调整方向 C.拉时用力，推时不用力 D.锯割过程中始终用力 B Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 5.如右图是用钢锯锯割角钢的场景，其中起锯操作符合规范的是（ ） C A D B C Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 6.如图所示是工件锯割加工的夹持方法，其中合理的是 A Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.金属材料的锉削 锉刀种类 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.金属材料的锉削 操作要领： a.锉削时要注意身体和手臂动作的协调 b.在推锉过程中，左手的施压要由大变小,右手的施压要由小变大，使锉刀平稳而不上下摆动 c.锉刀只推锉，回来时锉刀离开工件，再轻放到工件上进行推锉，推锉时一定要用力下压 d.姿势如