- 1、本文档共9页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
MCSS安装参数全解
MCSS PARAMETERS
SPEC-90, E311
EEPROM SETTING MANUAL VER. 2.5
M -- 2 -- 3
[ INST = 1 ]
Top floor job top floor number ( = bottom floor+53 ) 最高层 Bottom floor 0 bottom floor number ( = 0 ) 最底层 Country AJG 1 0 = NAO, 1 = JAPAN, 2 = ETO 控制型号。 ENABLE ADO NY (0) 0 = DISABLE, 1 = ENABLE 是否允许提前开门 ENABLE RELEVEL 1 0 = DISABLE, 1 = ENABLE 是否允许再平层 ADV BRK LIFT 0 0 = DISABLE, 1 = ENABLE ( NOT USED ) 是否允许提前打开抱闸 DBSS PARITY 0 0 = ODD, 1 = EVEN CAR NON START 20 s Max, permissible time for detecting door zone of next floor when running ( not used ) 经过两个插板允许的最大运行时间。 MAN. DECEL TIME 0 ( not used in Japan ) No. of DZ in 1LS 1 Number of door zone vane in 1LS zone 在1ls内,门区插板的数量 No. of DZ in 2LS 1 Number of door zone vane in 2LS zone 在2ls内,门区插板的数量 Abs. overspd % NOR 110% Ultra over-speed detection permissible % at normal running 正常运行期间,允许的最大超速。 Abs. overspd % INS 130 % Ultra over-speed detection permissible % at inspection running 检修运行期间,允许的最大超速。 Abs. overspd % REC 150 % Ultra over-speed detection permissible % at recover running 自平层运行期间,允许的最大超速。 Abs. overspd % REI 150 % Ultra over-speed detection permissible % at reinitialize running 复位运行期间,允许的最大超速。 Abs. overspd % JPSDO 120 % Ultra over-speed detection permissible % at terminal floor running on JPSDO Track err % NOR 25% Actual speed error permissible % at normal and reinitialize running 正常运行和复位运行时,允许和实际速度的误差。 Track err % INS 50% Actual speed error permissible % at inspection and recover running 检修运行时,允许和实际速度的误差。 Track err % LOW 255 % Actual speed error permissible % at relevel and learn running 再平层运行和自学习运行时,允许和实际速度的误差。 NTSD percent 97% Permissible speed at 1LS / 2LS detection ( % of Normal speed ) 1ls,2ls动作时电梯速度大于该设定值时,执行强迫减速功能(正常速度%) ETSD percent 94 % ETSD relay control speed ( % of Nor. speed ) ETSD继电器动作速度(正常速度%) Enable ETSD 1 0 = disable, 1 = enable ( relay fault detection ) 是否有ETSC功能。0=不允许,1=允许 PTR drop delay 10ms Timing for prepare-to-run drop after brake cut-off 0 : spec-90 /
您可能关注的文档
- mastercam曲面操作方法全解.doc
- M1U1_We_lived_in_a_small_house.全解.ppt
- matlab_zfc全解.ppt
- math数学全解.ppt
- MATLABsimulink在电机中的仿真全解.ppt
- MatlabCh5图形绘制全解.ppt
- matlab上机完美版全解.doc
- MATLAB图形工具箱全解.ppt
- Matlab原理与应用_5全解.ppt
- MATLAB基础教程第4章MATLAB图形绘制全解.ppt
- 10《那一年,面包飘香》教案.docx
- 13 花钟 教学设计-2023-2024学年三年级下册语文统编版.docx
- 2024-2025学年中职学校心理健康教育与霸凌预防的设计.docx
- 2024-2025学年中职生反思与行动的反霸凌教学设计.docx
- 2023-2024学年人教版小学数学一年级上册5.docx
- 4.1.1 线段、射线、直线 教学设计 2024-2025学年北师大版七年级数学上册.docx
- 川教版(2024)三年级上册 2.2在线导航选路线 教案.docx
- Unit 8 Dolls (教学设计)-2024-2025学年译林版(三起)英语四年级上册.docx
- 高一上学期体育与健康人教版 “贪吃蛇”耐久跑 教案.docx
- 第1课时 亿以内数的认识(教学设计)-2024-2025学年四年级上册数学人教版.docx
文档评论(0)