基于BFD MAD检测的IRF堆叠实验(H3C_ S5800系列).docxVIP

H3C S5800实现IRF功能详细配置过程一、网络说明：基于BFD MAD检测的IRF虚拟化实际操作配置，两台H3C_S5800交换机接口物理连接拓扑图如下图所示：两台交换机的两对万兆接口Ten-GigabitEthernet1/0/27和Ten-GigabitEthernet1/0/28作为IRF堆叠接口，千兆的GigabitEthernet1/0/24接口作为BFD MAD检测连接心跳线。二、交换机的配置：1、第一台交换机的配置：[H3C_S5800_1] irf member 1 renumber 1Warning: Renumbering the member ID may result in configuration change or loss. Continue?[Y/N]y // 系统有提示，不用管它，输入y继续配置[H3C_S5800_1] irf member 1 priority 32 // 修改IRF 优先级，越大越是Master[H3C_S5800_1] irf auto-update enable // 使能IRF 系统启动文件的自动加载功能[H3C_S5800_1] int Ten-GigabitEthernet1/0/27[H3C_S5800_1- Ten-GigabitEthernet1/0/27] shutdown //需要先提前关闭物理口，IRF 逻辑口要绑定物理口[H3C_S5800_1- Ten-GigabitEthernet1/0/27]quit[H3C_S5800_1] int Ten-GigabitEthernet1/0/28[H3C_S5800_1- Ten-GigabitEthernet1/0/28] shutdown[H3C_S5800_1 ] irf-port 1/2 //创建逻辑接口，注意对应。[H3C_S5800_1- irf-port 1/2] port group interface Ten-GigabitEthernet1/0/27 mode enhancedInfo: You are recommended to save the configuration after completing your IRF configuration; otherwise, // 系统有提示，不用管它[H3C_S5800_1- irf-port 1/2] port group interface Ten-GigabitEthernet1/0/28 mode enhanced[H3C_S5800_1- irf-port 1/2]quit[H3C_S5800_1] int Ten-GigabitEthernet1/0/27[H3C_S5800_1- Ten-GigabitEthernet1/0/27] undo shutdown[H3C_S5800_1- Ten-GigabitEthernet1/0/27] quit[H3C_S5800_1] int Ten-GigabitEthernet1/0/28[H3C_S5800_1- Ten-GigabitEthernet1/0/28] undo shutdown[H3C_S5800_1- Ten-GigabitEthernet1/0/28] quit[H3C_S5800_1] save // 保存，不然执行下步，设备会自动重启。The current configuration will be written to the device. Are you sure? [Y/N]:yPlease input the file name(*.cfg)[flash:/config.cfg](To leave the existing filename unchanged, press the enter key): Validating file. Please wait.... The current configuration is saved to the active main board successfully. Configuration is saved to device successfully.[H3C_S5800_1]quit H3C_S5800_1reboot Start to check configuration with next startup configuration file, please wait.........DONE! This command will reboot the device. Continue? [Y/N]:y#Apr 26 12:24:09:066 2000 H3C