590面板.docVIP

590面板 2 |__菜单 MENU LEVEL 3 | |__诊断 DIAGNOSTICS 4 | | |__[089] 速度给定 speed demand 4 | | |__[207] 速度反馈 speed feedback 4 | | |__[297] 速度错误 speed error 4 | | |__[549] 速度回路输出 spd loop output 4 | | |__[299] 电流给定 current dEmand 4 | | |__[298] 电流反馈 cerrent feedbanck 4 | | |__[538] 电流反馈AMPS current FBK AMPS 4 | | |__[065] IaFbk，未过滤的 iafbk unfiltered 4 | | |__[066] IaDmd，未过滤的 iadmd unfiltered 4 | | |__[087] 正电流钳位 POS.I CLAMP 4 | | |__[088] 负电流钳位 NEG.I CLAMP 4 | | |__[067] 实际正电流钳位 ACTUAL POS I LIM 4 | | |__[061]实际负电流钳位 ACTUAL NEG I LIM 4 | | |__[203] 所保留的反比时间O/P INVERSE TIME O/P 4 | | |__[042] 电流限值 AT CURRENT LIMIT 4 | | |__[077] 零速度 AT ZERO SPEED 4 | | |__[078] 零设定值 AT ZERO SETPOINT 4 | | |__[079] 停止 AT STANDSTILL 堵转跳闸 4 | | |__[113] 斜坡 RAMPING 4 | | |__[080] 程序性停止 PROGRAM STOP 4 | | |__[525] 惯性停止 COAST STOP 4 | | |__[082] 调速器的启动 DRIVE START 4 | | |__[084] 启用调速器 DRIVE ENABLD 4 | | |__[212] 运行模式 OPERATING MODE 4 | | |__[169] 已启用励磁 FIELD ENABLED 4 | | |__[183] 励磁给定 FIELD DEMAND 4 | | |__[300] 励磁电流反馈 FIELD I FBK 4 | | |__[539] 励磁电流反馈AMPS FIELD IFBKB AMPS 4 | | |__[181] RAW励磁电流反馈 RAW FIELD FBK 4 | | |__[184] 励磁射角 FLD FIRING ANGLE 4 | | |__[050] ANIN 1 (A2) ANIN1 4 | | |__[051] ANIN 2 (A3) ANIN2 4 | | |__[052] ANIN 3 (A4) ANIN3 4 | | |__[053] ANIN 4 (A5) ANIN4 4 | | |__[054] ANIN 5 (A6) ANIN5 4 | | |__[055] ANOUT 1 (A7) ANOUT1 4 | | |__[056] ANOUT 2 (A8) ANOUT2 4 | | |__[068] 启动(C3) START(C3) 4 | | |__[069] 数字输入端 C4 DIGITAL INPUT C4 4 | | |__[070] 数字输入端 C5 DIGITAL INPUT C5 4 | | |__[071] DIGIN 1 (C6) DIGIN1 C6 数字输入 DIGIN2 C7 数字输入 DIGIN3 C8 数字输出 1(B5) DIGOUT1 数字输出 2(B6) DIGOUT2 数字输出 3(B7) DIGOUT3 上升/下降输出 RAISE/LOWER O/P 设定值总1输出 SPT SUM OUTPUT 斜坡输出 RAMP OUTPUT 速度设定值 speed setpoint 端电压 TERMINAL VOLTS 反电动势 BACK EMF 测速发电机输入 TACH INPUT (B2) RAW测速器输入 RAW TACH INPUT 编码器 ENCODER 原始编码器RPM RAW ENCODER RPM PID误差 PID ERROR PID限幅 PID CLAMPED PID输出 PID OUTPUT 4 | | |__[083] 闭式接触器 CONTACTOR CLOSED 4 | | |__[122] 正常指示灯 HEALTH LED 4 | | |__[125] 准备就绪 READY 4 | | |__[376] 运行中的调速器 DRIVE RUN