基于multisim的互补输出电路仿真测试试编.docxVIP

基于Multisim互补输出电路的仿真测试摘 要随着集成电路的广泛应用，其电路的输出级也在不断的变化中，大多数输出电路采用互补输出形式，由于互补输出电路具有输出正负方向对称，双向跟随，带负载能力强等特点，常作为直接耦合多级放大电路的输出级。在集成运放电路输出级中互补输出电路不仅作为其输出级用于带动负载，也作为集成功率放大器的输出级形式。本文介绍了互补输出的基本电路以及两种消除交越失真的互补输出级，并针对选定的晶体管等元件参数，应用Multisim10.0进行了仿真，主要包括静态时晶体管基极和发射极电位，以及动态时输入与输出波形的峰值、幅频及失真性等，通过对数据分析，得出该互补电路适合大多数电路输出级设计以及双向跟随特性。关键词：互补输出级,交越失真，Mulitisim10AbstractAlong with the extensive application of integrated circuit, the circuit of the output stage is also in constant change, most of the output circuit using complementary output form, due to complementary output circuit with output positive and negative direction symmetry, two-way follow, with strong ability to load characteristics, often as directly coupled multi-stage amplification circuit of the output stage.In the integrated operational amplifier circuit output stage complementary output circuit not only as the output stage is used to drive the load, also serves as an integrated power amplifier output stage form.This paper introduces the complementary outputs of the basic circuit and two eliminate distortion is complementary output stage, and according to the selected transistor elements such as parameters, the application of multisim10.0 simulation, mainly including static transistor base and emitter potential, as well as dynamic input and output waveform peak, amplitude frequency and distortion, through the analysis of the data that the complementary circuit suitable for most of the output stage circuit design and two-way following characteristics.Keywords: Complementary output stage, crossover distortion, Mulitisim10目 录1绪论12互补输出电路的工作原理22.1基本互补输出电路22.2消除交越失真的互补输出级33仿真测试的目的、方法和要求53.1消除互补输出级交越失真电路测试仿真的目的53.2搭建消除互补输出级交越失真的测试电路53.3掌握消除交越失真电路的原理与波形特点53.4仿真内容64对消除互补输出级交越失真的仿真分析64.1搭建基本互补和消除交越失真互补输出级电路64.2静态测试和动态测试74.3仿真测试的分析与结论104.3.1基本互补输出电路的仿真分析104.3.2消除交越失真的互补输出级电路的仿真分析105结语106参考文献11绪论互补输出电路作为直接耦合多级放大电路的输出级,本文对互补输出电路的基本原理进行了具体阐述，并对其交越失真的产生和如何消除做了说明，至于元件参数的选择，首先通过理论估算，再通过Multisim进行仿真，测量了电路的静态工作点，基本做到零输入零输出，结构简单，分立元件的数量相对较少，动态调