- 1、本文档共5页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
The Key Stamping Process Analysis and Mold Design
The key stamping process analysis and mold design
Guolin Wang
Shandong Transport Vocational College ,Shandong Weifang ,261206,China;
E-mail: 572407372@
Key words: key, stamping, process, mold
Abstract: key production into mass production, the aluminum alloy material, including punching,
blanking, two working procedure, precision parts, determine the first punch blanking, after adopting
progressive die production. For mould design and calculation, and the convex model component
and its structure, die components, positioning parts, unloading and push the pieces of parts to carry
on the design, to complete the mold assembly drawing.
1. The stamping technology analysis of blank keys
As shown in figure 1, parts production to mass production, the material is 2 mm thick aluminum
alloy plate. There is hole. The artifacts including punching, blanking, two working procedure,
precision parts, all take the free size of workpiece, ordinary mold can meet.
Fig.1 Key part drawing
2. The scheme determination of stamping
The artifacts including blanking, punching and cutting edge, can have the following plan:
Scheme 1: punching blanking, after first USES the level into a mold production.
Scheme 2: blanking - bending - punching compound stamping, with composite mold production.
Focus two mould process, forming at a time. But abrasive complex, various parts of the
processing difficulty is big, need more parts and complex; Plan a need a pair of mold production
efficiency while the mould structure complex but simple geometry mould manufacturing is not
difficult, because parts by comparing these methods, the scheme adopts the scheme one is preferred.
3. The layout and sure
Stamping on the strip or sheet metal decorate a method known as the layout. Layout of the principle
is the same as the ordinary cutting. If parts are not required to rolling direction of the material, the
layout of the aim is to ensure that process needs and ensure that the workpiece cutting
您可能关注的文档
- Solo80打印机 Memory-card manual.pdf
- Solitary-wave description of condensate micro-motion in a time-averaged orbiting potential.pdf
- SoM SD Card应用实测.pdf
- Some Applications of the Spectral Shift Operator.pdf
- Some comments on the handbag approach to wide-angle exclusive scattering.pdf
- Some Estimates on the Boltzmann Collision Operator.pdf
- Some Experiments on Fitting of Gielis Curves by Simulated Annealing and Particle Swarm Meth.pdf
- Some Description Logic.pdf
- Some new theorems of expanding mappings without continuity.pdf
- Some models for estimating technical and scale inefficiencies in data envelopment analysis_R.D.Banke.pdf
文档评论(0)