cisco 9124 光纤交换机配置.doc

下载文档 降价啦

63
0
约7.87千字
约 7页
2017-04-19 发布于湖北
举报
版权申诉
保障服务

cisco 9124 光纤交换机配置.doc

1、本文档共7页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

cisco 9124 光纤交换机配置

命令行方式 CISCO 的交换机和普通的博科或者QLOGIC的交换机差别很大。普通的交换机直接进入默认IP地址，通过图形化界面直接配置就OK了。CISCO的交换机没有图形界面，因此解决需要如下配置步骤： 1、察看每个端口状态： switch2# show interface fc1/1 fc1/1 is up Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN) Port WWN is 20:01:00:0d:ec:be:0d:40 Admin port mode is auto, trunk mode is on snmp link state traps are enabled Port mode is F, FCID is 0xd40300 Port vsan is 1 Speed is 4 Gbps Rate mode is dedicated Transmit B2B Credit is 8 Receive B2B Credit is 16 Receive HYPERLINK javascript:; \t _self data field Size is 2112 Beacon is turned off 5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec 5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec 378 frames input, 17228 bytes 0 discards, 0 errors 0 CRC, 0 unknown class 0 too long, 0 too short 56 frames output, 3536 bytes 0 discards, 0 errors 3 input OLS, 3 LRR, 0 NOS, 13 loop inits switch2# show interface fc1/2 fc1/2 is up Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN) Port WWN is 20:02:00:0d:ec:be:0d:40 Admin port mode is auto, trunk mode is on snmp link state traps are enabled Port mode is F, FCID is 0xd40500 Port vsan is 1 Speed is 4 Gbps Rate mode is dedicated Transmit B2B Credit is 3 Receive B2B Credit is 16 Receive data field Size is 2112 Beacon is turned off 5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec 5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec 11839 frames input, 476672 bytes 0 discards, 0 errors 0 CRC, 0 unknown class 0 too long, 0 too short 161 frames output, 8952 bytes 0 discards, 0 errors 1 input OLS, 1 LRR, 0 NOS, 33 loop inits switch2# show interface fc1/3 fc1/3 is down (Link failure: Link Reset) Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN) Port WWN is 20:03:00:0d:ec:be:0d:40 Admin port mode is auto, trunk mode is on snmp link state tra