拉深模设计讲述.docxVIP

落料拉深冲孔复合模设计报告  TOC \o 1-3 \h \z \u  HYPERLINK \l _Toc453611444 1 绪论  PAGEREF _Toc453611444 \h 4  HYPERLINK \l _Toc453611445 2 成型工艺  PAGEREF _Toc453611445 \h 5  HYPERLINK \l _Toc453611446 2.1 制件结构尺寸  PAGEREF _Toc453611446 \h 5  HYPERLINK \l _Toc453611447 2.2 工艺设计  PAGEREF _Toc453611447 \h 5  HYPERLINK \l _Toc453611448 2.2.1 修边余量确定  PAGEREF _Toc453611448 \h 5  HYPERLINK \l _Toc453611449 2.2.2 毛坯尺寸计算  PAGEREF _Toc453611449 \h 5  HYPERLINK \l _Toc453611450 2.2.3 确定拉深次数  PAGEREF _Toc453611450 \h 6  HYPERLINK \l _Toc453611451 2.2.4 确定拉深内径  PAGEREF _Toc453611451 \h 6  HYPERLINK \l _Toc453611452 2.2.5 凹模圆角半径的确定  PAGEREF _Toc453611452 \h 6  HYPERLINK \l _Toc453611453 2.2.6 凸模圆角半径的确定  PAGEREF _Toc453611453 \h 6  HYPERLINK \l _Toc453611454 2.2.7 拉深件高度确定  PAGEREF _Toc453611454 \h 6  HYPERLINK \l _Toc453611455 2.2.8 拉深模间隙确定  PAGEREF _Toc453611455 \h 7  HYPERLINK \l _Toc453611456 2.2.9 压边圈选用  PAGEREF _Toc453611456 \h 7  HYPERLINK \l _Toc453611457 3 模具结构设计  PAGEREF _Toc453611457 \h 7  HYPERLINK \l _Toc453611458 3.1 模具尺寸  PAGEREF _Toc453611458 \h 7  HYPERLINK \l _Toc453611459 3.1.1 落料模  PAGEREF _Toc453611459 \h 7  HYPERLINK \l _Toc453611460 3.1.2 拉伸模  PAGEREF _Toc453611460 \h 8  HYPERLINK \l _Toc453611461 3.2 冲压力计算  PAGEREF _Toc453611461 \h 8  HYPERLINK \l _Toc453611462 3.2.1 落料力  PAGEREF _Toc453611462 \h 8  HYPERLINK \l _Toc453611463 3.2.2 拉深力  PAGEREF _Toc453611463 \h 8  HYPERLINK \l _Toc453611464 3.2.3 压边力  PAGEREF _Toc453611464 \h 9  HYPERLINK \l _Toc453611465 3.2.4 卸料力  PAGEREF _Toc453611465 \h 9  HYPERLINK \l _Toc453611466 3.2.5 冲孔力  PAGEREF _Toc453611466 \h 10  HYPERLINK \l _Toc453611467 4 冲裁排样  PAGEREF _Toc453611467 \h 10  HYPERLINK \l _Toc453611468 4.1 排样方案  PAGEREF _Toc453611468 \h 10  HYPERLINK \l _Toc453611469 4.2 材料利用率  PAGEREF _Toc453611469 \h 11  HYPERLINK \l _Toc453611470 5 压力机选择  PAGEREF _Toc453611470 \h