模具相关基础英语培训-复习课要点.pptVIP

英语培训 冷冲压模具 中文名称 英文名称 对应音标 中文名称 英文名称 对应音标 连续模 progressive die [pr?gres?v] [da?] 冲孔模 pierce die [p??s] [da?] 机械手 transfer die [tr?nsf??][da?] 修边模 trim die [tr?m] [da?] 手动机械手 hand transfer die [h?nd][tr?nsf??] [da?] 下料模 blanking die [bl??ki?] [da?] 单工程模 single die [s??g(?)l] [da?] 成形模 forming die [f??m??] [da?] 铸造结构模 casting die [kɑ?st??] [da?] 折弯模 bending die [bend??] [da?] 简易模 prototype die [pr??t?ta?p] [da?] 翻边模 flange die [fl?n(d)?] [da?] 铆合模 riveting die [r?v?t??] [da?] 拉伸模 draw die [dr??][da?] 复合模 compound die [k?mpa?nd] [da?] 快换模 changeable die [t?e?n(d)??b(?)l] [da?] 料带 strip [str?p] 料带图 strip layout [str?p] [le?a?t] 工序 process [pr??ses] 冲导正孔 pierce pilot [p??s] [pa?l?t] 冲孔 pierce [p??s] 侧冲 cam pierce [k?m] [p??s] 摆料带 tip [t?p] 切侧刃缺口 notch [n?t?] 折弯 bend [bend] 墩薄 coin [k??n] 成形 form [f??m] 侧成形 cam form [k?m] [f??m] 整形 restrike [r?：stra?k] 翻边/法兰 flange [fl?n(d)?] 打凸米 dimple [d?mp(?)l] 打凸包 emboss [?mb?s; em-] 打字印 stamp [st?mp] 打沙拉孔 hourglass [a??glɑ?s] 面押 coin burr [k??n] [b??] 抽孔 extrude hole [?kstru?d; ek-][h??l] 拍平 flat [fl?t] 卷圆 curl [k??l] 中文名称 英文名称 对应音标 中文名称 英文名称 对应音标 拼接线 切断 分离 joint line cutoff separate [d???nt] [la?n] [k?t,??f] [sep(?)r?t] 接刀口 mismatch cookie bite over cut [m?sm?t?] [k?k?] [ba?t] [??v?] [k?t] 料带带料处 carrier tab [k?r??] [t?b] 毛刺 burr [b??] 光亮带 burnish [b??n??] 塌角 roll over [r??l] [??v?] 毛刺方向 burr direction [b??] [d?rek?(?)n; da?rek?(?)n] 断裂带 fracture [fr?kt??] 中文名称 英文名称 对应音标 中文名称 英文名称 对应音标 旋转 rotate [r?(?)te?t] 铆接 rivet [r?v?t] 切边线 trim line [tr?m] [la?n] 铆螺母 nut [n?t] 落料 blanking [bl??ki?] 修边线 trim line [tr?m] [la?n] 板料 blank [bl??k] 中心线 center line [s?nt?] [la?n] 拉延 draw ?[dr??] 坯料线 blank line [bl??k] [la?n] 分模线 P.O. line punch outline ?[p?n(t)?] [a?tla?n] CH孔 coordinate hole ?[ko?rd?net] [h??l] 到底标记 bottom mark ?[b?t?m] ?[mɑ?k] 拉延后坯料线 blank line after draw [bl??k] [la?n] [ɑ?ft?] [dr??] 破裂刀 split cutter [spl?t] ?[k?t?] 单动拉延 双动拉延 反向拉延 single action draw ?[s??g(?)l] [?k?(?)n] double action draw ?[d?