木工压刨床(单面和多面)安全操作规程.docVIP

木工压刨床(单面和多面)安全操作规程 木工压刨床安全操作规程提要：操作时，应按顺序连续送料，并须保持平整和垂直于刨刃.如发现材料走横或卡住，应停机降低台面拨正，再开机继续进刨 来自 木工压刨床安全操作规程 一、机床只准采用单向开关，不准安装倒顺双向开关，并要按顺序开动. 二、送料和接料人员不准戴手套，并应贴着被刨料的一侧，而不能正对刨口.作业时，严禁一次刨削两块不同材质，规格的木料，被刨木料的厚度不得超过50mm.送料时，手指必须离开滚筒200mm以外，接料人员须待被刨料走出台面后，方准接料. 三、操作时，应按顺序连续送料，并须保持平整和垂直于刨刃.如发现材料走横或卡住，应停机降低台面拨正，再开机继续进刨. 四、每次进刀量应为2-5mm，如遇硬木或木节，除了减小进刀量外，还应降低进料速度. 五、进料时，须先进大头并随时注意和防止被刨木料回弹. 六、被刨木料长度不能短于前后压滚的中心距离;刨短料时须连续进料，如材料不走时，可用其它材料推进，不许用手推动.刨削厚度小于10mm的薄板时，必须垫托板方可推进压刨. 七、小于工作台面宽度的装配式框扇一类的工件，允许在压刨上进行刨削，但必须斜着进给，其斜度应不大于30°.同时，进给速度要慢，进刀深度要浅. 八、刨刀与刨床台面的水平间隙应在10-30mm之间，同一台刨机的刀片和刀片螺丝的重量，厚度必须一致，刀架夹板必须平整贴紧.合金刀片焊缝超出刀头和有裂缝的刀具不准使用.刀片紧固螺栓应嵌入刀片槽内，槽端离刀背不得小于100mm.紧固刀片螺丝用力应均匀一致，不得过紧或过松，严禁使用带口槽的刨刀. 九、压刨必须装有回弹灵敏的逆上爪装置，进料齿辊及托料光辊应调整水平和上下距离一致，齿辊应低于工件表面1-2mm，光辊应高出台面，工作台面不得歪斜和高低不平. 十、操作中如发现故障时，应立即切断电源，并待停止运转后进行修理. 来自 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good qualit