木扶手制作安装施工方法与技术措施.docVIP

木扶手制作安装施工方法与技术措施 木扶手制作安装施工方法与技术措施提要：扶手弯头制作：在制作弯头前，应做足尺样板。做弯头的整料先斜纹出方，然后按样板画好线，用窄条锯锯出皱型毛料，毛料尺寸一般比实际尺寸大10mm左右 木扶手制作安装施工方法与技术措施 1、木扶手、弯头制作 （1）木扶手制作：木扶手具体形式和尺寸应按设计要求制作。扶手底开槽深度一般为3-4mm，宽度依所用扁铁的尺寸，但不得超过40mm。在扁铁上每隔300mm钻孔，一般用32mm的木螺钉固定。木扶手制作前，应按设计要求作出扶手的横断面样板，将扶手底刨平、刨直后，划出中线，在两端对好样板划出断面，然后将底部的木槽刨出，再用线刨依顶头的断面线刨出成型，刨时注意留半线，以免净面时污料。 （2）扶手弯头制作：在制作弯头前，应做足尺样板。做弯头的整料先斜纹出方，然后按样板画好线，用窄条锯锯出皱型毛料，毛料尺寸一般比实际尺寸大10mm左右。先把弯头底做准，然后在扶手样板顶划线，用刨刨平，注意要留线，防止与扶手连接时污料。 2、木扶手、弯头安装 （1）安装扶手应由下往上进行，首先按照栏杆斜度配好起步的弯头，再接扶手，其高低要符合设计要求。扶手与弯头的接头在下边作暗榫，用铁活铆固。与铁栏杆连接用的木螺钉应拧紧，螺帽不得外露，间距不得大于400mm，弯头易掉，安装必须牢固。 （2）安装扶手时，依据靠踏步一面的栏板或栏杆为准，全部安装完，要修接头。根据木扶手坡度、形状，用扁铲将弯头加工成形，再小刨刨光，最后用砂纸磨光。 （3）扶手末端与墙连接，将扶手底部通长扁钢与墙内预埋件焊牢，扁钢与木扶手用木螺钉固定。 （4）扶手安装完毕，刷一遍干性油，防止受潮变形。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and imag