木门安装施工方法（七）.docVIP

木门安装施工方法（七） 木门安装施工方法（七）提要：门框安装1）安装时按设计图纸要求的水平标高和平面位置，对应编码安放。用通线及线锤作水平和吊直校正，然后用拉条与邻近固定物连接牢靠 自 木门安装施工方法（七） 常用机具为：粗刨、细刨、裁口刨、单线刨、锯、锤子、改锥、线勒子、扁铲、塞尺、线坠。 1）施工准备 （1）室外水平线已弹好。 （2）门框、扇在安装前应检查无窜角、翘扭、弯曲、劈裂、崩缺等，如有上述情况应进行处理； （3）门框进场后，组织涂料工将预埋木砖及木门框靠墙体或砼接触的部分涂刷防腐材料，刷油后类码放平整，底层应垫平、垫高，露天堆放的应用塑料布遮盖好； 2）操作工艺 A、门框安装 （1）安装时按设计图纸要求的水平标高和平面位置，对应编码安放。用通线及线锤作水平和吊直校正，然后用拉条与邻近固定物连接牢靠。砌墙前安框，应按设计要求在边框装设埋墙铁脚码（磨耳码）。 （2）在砌体预留木砖，每边固定点不少于三处，其间距不大于~。用木楔将框临时固定在门洞内后，将框用砸扁钉帽的钉钉牢在木砖上，钉槽凹入1~2mm。安装时应考虑抹灰层厚度，立框时与抹灰外皮平。 B、门扇安装 （1）按照图纸及设计要求确定开启方向和使用小五金、门锁型号规格。 （2）用尺量框内上、中、下尺寸，对应画在门扇上，修刨后先塞入框内校对，如不合适再画线进行修刨直至合适为止。 （3）门扇立挺与框接合部分要刨成斜面，以不影响缝隙为准。 （4）门扇开启后易碰墙，为固定门扇位置应安装门轧头。 c、门小五金的安装 （1）合页铰距门上、下端宜取立挺高度的1/10，并避开上下冒头，安装后应开关灵活。 （2）小五金均应用木螺丝固定，不得用钉子代替，应先用锤打入1/3深度，然后拧入，严禁打入全部深度。 （3）小五金要安装齐全，位置适宜，固定可靠。 自 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good qual