钢筋制作安装施工安全防护.docVIP

钢筋制作安装施工安全防护 钢筋制作安装施工安全防护提要： 更多内容源自绿化 钢筋制作安装 第一节制作、绑扎 、钢材、半成品等应按规格、品种分别堆放整齐,制作场地要平整,工作台要稳固,照明灯具必须加网罩。 2、拉直钢筋,卡头要卡牢,地锚要结实牢固,拉筋沿线2米区域内禁止行人。人工绞磨拉直,不准用胸、肚接触推杠,并缓慢松解,不得一次松开。 3、展开盘圆钢筋要一头卡牢,防止回弹,切断时要先用脚踩紧。 4、人工断料,::工具必须牢固。掌克子和打锤要站成斜角,注意扔锤区域内的人和物体。切断小于30厘米的短钢筋,应用钳子夹牢,禁止用手把扶,并在外侧设置防护的箱笼罩。 5、多人合运钢筋,起、落、转、停动作要一致,人工上下传送不得在同一垂直线上,钢盘堆放要分散、稳当,防止倾倒和塌落。 6、在高空、深坑绑扎钢筋和安装骨架,须搭设脚手架和马道。 7、绑扎墙体钢筋,不得站在钢筋骨架上下。 8、绑扎基础钢筋时,应按施工设计规定摆放钢筋支架或马凳架起上部钢筋,不得任意减少支架或马凳。 9、起吊钢筋骨架,下方禁止站人,必须待骨架降落到离地1米以内始准靠近,就位支撑好方可摘钩。 第二节冷拉 、冷拉卷扬机前应设置防护挡板,没有挡板时,应将卷扬机与冷拉方向成90度,并且应用封闭式导向滑轮。操作时要站在防护挡板后,冷拉场地不准站人和通行。 2、冷拉钢筋要上好夹具,离开后再发开车信号。发现滑动或其它总是时要先行停车,放松钢筋后,才能重新进入操作。 3、冷拉钢筋要严格按照规定应力和伸长率进行,不得随便变更。不论拉伸或放松钢筋都应缓慢均匀。 第三节点焊、对焊机 、焊机应设在干燥的地方,平稳牢固,要有接地装置,导线绝缘良好。 2、焊接前,应根据钢筋截面调整电压,发现焊头漏电,即更换,禁止使用。 3、操作时应戴防护眼镜和手套,并站在橡胶板或木板上,工作棚要用防火材料搭设。棚内堆放易燃、易爆物品,并备有灭火器材。 4、对焊机断路器的接触点、电极,要定期检查修理,冷却水管保持畅通,不得漏水和超过规定温度。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy