钢筋操作工艺要求-楼板钢筋施工工艺.docVIP

钢筋操作工艺要求:楼板钢筋施工工艺 钢筋操作工艺要求:楼板钢筋施工工艺提要：工艺流程：清理模板→模板上画钢筋位置线→绑板下受力筋及其分布筋→水电配合→垫砼马凳→绑负弯矩钢筋及其分布筋 楼板钢筋工艺 1）工艺流程：清理模板→模板上画钢筋位置线→绑板下受力筋及其分布筋→水电配合→垫砼马凳→绑负弯矩钢筋及其分布筋. 2）清理模板上面的杂物，用墨线弹好主筋，分布筋间距线。 3）按划好的间距，先摆放受力主筋、后放分布筋，预埋件、电线管、预留孔等及时配合安装； 4）绑扎板筋用顺扣或八字扣，不得全部用同向顺扣绑扎。板筋要求全部绑扎。 5）楼板底筋保护层厚为15mm，采用塑料垫块控制保护层厚度，间距为×布置。 6）绑完下排筋后，加砼马凳（如下图），根据楼板厚度及上下层钢筋直径制作，在砼马凳制作前须由项目部钢筋工长审核制作高度。制作完成一批须经预检合格方可使用。 7）现浇板除注明者外，分布钢筋的截面面积不应小于主筋的10%（每米宽度内）且不小于Φ6@600。 8）板上开洞按设计要求加洞边加强筋； 9）板筋端部锚固应符合设计要求； 10)本工程对板负筋的特别设计要求： 4楼梯钢筋绑扎: 1）工艺流程:划位置线-绑梯梁筋-绑板主筋-绑板分布筋-绑踏步筋。 2）在楼梯底板上划主筋和分布筋的位置线； 3）绑梁主筋及梁箍筋； 4）根据设计图纸中主筋、分布筋的方向，先绑扎主筋、后绑分布筋，每个交点均应绑扎，板筋要锚固到梁内； 5）底板筋绑完，待踏步模板吊绑支好后，再绑扎踏步筋，主筋接头数量和位置均要符合施工规范的规定。 5暗柱筋在操作层上口300mm设定位箍一道。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and