- 1、本文档共13页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
小天鹅滚筒洗衣机拆装方法(国外英文资料)
小天鹅滚筒洗衣机拆装方法(国外英文资料)
Maintenance manuals
Little swan
Platen washing machine
E XQG65-908.
Es XQG65-958.
E XQG65-1028.
El XQG70-968.
Esl XQG65-1018.
Esl XQG70-1088.
XQG70-1008 - c
Cs XQG70-1098.
Cs XQG70-1228.
The method of dismantling the main parts and parts
One, maintenance common tools
tool
specifications
use
Phillips screwdriver
The commonly used
A screwdriver
The commonly used
vise
The commonly used
Long nose pliers
The commonly used
Socket wrench
10, 13,
10 - heat pipe, 13-balance block, transport screw
Flat wrench
17
Adjust foot level
multimeter
Check the circuit
Adjustable spanner
Install the faucet
level
Washing machine adjust level
The removal of the washing machine before the washing machine is used
Remove the transport screws
The drum of the drum washing machine is assembled in the box in the form of whole load. In order to avoid the washing machine barrel and the outer casing of transit collide with each other, in the factory, the outer barrel loading and box body is transported by four screws together. When installing a washing machine, therefore, should first dismantled transport screws by 13 (hand), transport screws should be properly kept after take off, in case in the washing machine with transport.
Transport screw
Adjust the base Angle
The four bottom feet of the washer are used to adjust the balance of the washing machine. After washing machine is in place, with 17 will move hand four foot nut unscrew down, adjust the foot screws with the hand, the balance of the washing machine, then use upward twist foot nut and screw at the bottom of the box body tightly.
The installation of the inlet pipe
The incoming water pipe will be carried on the faucet, and the other end will be installed in the washer and water solenoid valve.
Installation of drains
Platen washing machine drains should be hung up, general outlet end of the highest position may not be 100 cm above the bottom of the washing machine, the lowest shall be not less than 60 centimeters, or wi
您可能关注的文档
- 大工11秋《水电站修建物》在线功课2(国外英文资料).doc
- 大工12春《工程力学》(二)在线功课3(国外英文资料).doc
- 大工12春《工程项目治理》在线功课2(国外英文资料).doc
- 大工11秋《钢筋混凝土结构》在线功课2(国外英文资料).doc
- 大工12秋《房屋修建学》在线功课2谜底(国外英文资料).doc
- 大工12秋《钢结构》 在线功课1(国外英文资料).doc
- 大工13春《公司金融》在线功课1(国外英文资料).doc
- 大工13春《土木工程概论》在线测试3(国外英文资料).doc
- 大工13春《钢结构》功课谜底3(国外英文资料).doc
- 大工13秋《修建资料》指点资料十一(国外英文资料).doc
文档评论(0)