DXP2004实训报告.docVIP

实训报告 科目：PCB设计与布板技术 实训项目： 班别： 姓名： 学号： 系别： 专业： 指导老师： 绘制电路图 二、元器件参数对应封装选择及说明 本次设计元器件的参数及封装如下： Description Designator Footprint LibRef Quantity Polarized Capacitor (Axial) C1 CAPPR2-5x6.8 Cap Pol2 1 Typical INFRARED GaAs LED DS1~D56 CAPPR2-5x6.8 LED0 1 NPN Bipolar Transistor Q1 ~Q8 SFM-T3/A4.7V NPN 1 Resistor R1~R26 AXIAL-0.4 Res2 1 Potentiometer RP1 VR5 Rpot 1 Serial-In Parallel-Out Shift Register U1 DIP-14 SN74LS164N 1 General-Purpose Single Bipolar Timer U2 DIP-8 NE555N 1 上表列出的是电路图所需要元器件的所有封装，其中C1和C3都选择了CAPPR2-5x6.8型号的封装，其他的电容封装都选择了RAD-0.1型号的封装，DS1到DS56都选择了CAPPR2-5x6.8型号的封装，这可以看出不同的元器件可以用相同的封装，对于各种元器件的封装，我们要选择恰当，才能更好的布局，元器件的封装的选择不仅影响布局而且还影响布线，从而影响整个PCB板的设计，所以在选择封装时要慎重考虑好影响整个PCB板的主要因素，为制作良好的PCB板做铺垫。 三、ERC与网络表 ERC电路规则检查没有错误，所以整个电路图是没有错；网络表是检查电路图有没有封装和漏接线的工具，生成网络表如下图所示： [ U2 DIP-8 NE555N ] [ U1 DIP-14 SN74LS164N ] [ RP1 RP1 RPot ] [ R12 AXIAL-0.4 Res2 ] [ R11 AXIAL-0.4 Res2 ] [ R10 AXIAL-0.4 Res2 ] [ R9 AXIAL-0.4 Res2 ] [ R8 AXIAL-0.4 Res2 ] [ R7 AXIAL-0.4 Res2 ] [ R6 AXIAL-0.4 Res2 ] [ R5 AXIAL-0.4 Res2 ] [ R4 AXIAL-0.4 Res2 ] [ R3 AXIAL-0.4 Res2 ] [ R2 AXIAL-0.4 Res2 ] [ R1 AXIAL-0.4 Res2 ] [ Q8 SFM-T3/A4.7V NPN ] [ Q7 SFM-T3/A4.7V NPN ] [ Q5 SFM-T3/A4.7V NPN ] [ Q4 SFM-T3/A4.7V NPN ] [ Q3 SFM-T3/A4.7V NPN ] [ Q2 SFM-T3/A4.7V NPN ] [ Q1 SFM-T3/A4.7V NPN ] [ DS56 CAPPR2-5x6.8 LED0 ] [ DS55 CAPPR2-5x6.8 LED0 ] [ DS54 CAPPR2-5x6.8 LED0 ] [ DS53 CAPPR2-5x6.8 LED0 ] [ DS52 CAPPR2-5x6.8 LED0 ] [ DS51 CAPPR2-5x6.8 LED0 ] [ DS50 CAPPR2-5x6.8 LED0 ] [ DS49 CAPPR2-5x6.8 LED0 ] [ DS48 CAPPR2-5x6.8 LED0 ] [ DS47 CAPPR2-5x6.8 LED0 ] [ DS46 CAPPR2-5x6.8 LED0 ] [ DS45 CAPPR2-5x6.8 LED0 ] [ DS44 CAPPR2-5x6.8 LED0 ] [ DS43 CAPPR2-5x6.8 LED0 ] [ DS42 CAPPR2-5x6.8 LED0 ] [ DS41 CAPPR2-5x6.8 LED0 ] [ DS40 CAPPR2-5x6.8 LED0 ] [ DS39 CAPPR2-5x6.8 LED0 ] [ DS38 CAPPR2-5x6.8 LED0 ] [ DS37 CAPPR2-5x6.8 LED0 ] [ DS36 CAPPR2-5x6.8 LED0 ] [ DS35 CAPPR2-5x6.8 LED0 ] [ DS34 CAPPR2-5x6.8 LED0 ] [ DS33 CAPPR2-5x6.8 LED0 ] [ DS32 CAPPR2-5x6.8 LED0 ] [ DS31 CAPPR2-5x6.8 LED0 ] [ DS30