计算完钢立柱后且修改后创新项目.docx

工字钢 工字钢上所受荷载 作用在支架上的箱型梁上混凝土分布面积A（㎡）A1A2A3A4A5A6A7A8A9A10A110.190.20.270.340.256.980.250.340.270.20.19作用在支架上的模板长度L(m)L1L2L3L4L5L6L7L8L9L10L110.990.60.60.60.3628.880.360.60.60.60.99作用在箱型梁上的施工荷载的长度L（m）L1L2L3L4L5L6L7L8L9L10L110.770.60.60.60.366.340.360.60.60.60.77作用在每个支架上箱型梁的混凝土自重Pa（KN）Pa1Pa2Pa3Pa4Pa5Pa6Pa7Pa8Pa9Pa10Pa110.980.590.590.590.3528.590.350.590.590.590.98作用在每个支架上的模板自重Pb（KN）Pb1Pb2Pb3Pb4Pb5Pb6Pb7Pb8Pb9Pb10Pb111.851.441.441.440.8615.220.861.441.441.441.85作用在每个支架上的施工荷载的力Pc（KN）Pc1Pc2Pc3Pc4Pc5Pc6Pc7Pc8Pc9Pc10Pc113.263.434.635.834.29119.784.295.834.633.433.26∑P=Pa+Pb+Pc（KN）6.095.466.667.865.5163.595.57.866.665.466.09中间箱室作用在方木上的长度L=5.4m 所以转换为均布荷载= 其中作用在每个支架上箱型梁的混凝土自重: Pa=1.1A0.626 作用在每个支架上的模板自重: Pb=1.1L0.61.5 作用在每个支架上的施工荷载的力: Pc=L0.64 冲击系数为1.1，每片贝雷片的间距为0.6m，混凝土的容重为26KN/m3，模板的分布荷载为1.5KN/㎡，施工荷载的分布荷载为4KN/㎡，施工荷载已经考虑了冲击系数，因此求解公式为Pc=L0.64 工字钢（20a号）截面特性： 理论质m=27.9kg/m E=206GP, A=35.578cm2 IX=2370cm4 Iy=158cm4 EA=732900KN EI=5150KN.m 所建力学模型如下图 用结构力学求解编码如下 结点,1,0.9,0 结点,2,1.8,0 结点,3,2.7,0 结点,4,3.6,0 结点,5,4.05,0 结点,6,4.5,0 结点,7,4.95,0 结点,8,5.85,0 结点,9,6.75,0 结点,10,7.65,0 结点,11,8.1,0 结点,12,8.55,0 结点,13,9,0 结点,14,9.9,0 结点,15,10.8,0 结点,16,11.7,0 结点,17,12.6,0 结点,18,0,0 单元,1,2,1,1,1,1,1,1 单元,2,3,1,1,1,1,1,1 单元,3,4,1,1,1,1,1,1 单元,4,5,1,1,1,1,1,1 单元,5,6,1,1,1,1,1,1 单元,6,7,1,1,1,1,1,1 单元,7,8,1,1,1,1,1,1 单元,8,9,1,1,1,1,1,1 单元,9,10,1,1,1,1,1,1 单元,10,11,1,1,1,1,1,1 单元,11,12,1,1,1,1,1,1 单元,12,13,1,1,1,1,1,1 单元,13,14,1,1,1,1,1,1 单元,14,15,1,1,1,1,1,1 单元,15,16,1,1,1,1,1,1 单元,16,17,1,1,1,1,1,1 单元,18,1,1,1,1,1,1,1 结点支承,18,3,0,0,0 结点支承,1,1,0,0 结点支承,14,1,0,0 结点支承,15,1,0,0 结点支承,16,1,0,0 结点支承,17,1,0,0 结点支承,2,1,0,0 结点支承,3,1,0,0 结点支承,4,1,0,0 结点支承,5,1,0,0 结点支承,6,1,0,0 结点支承,7,1,0,0 结点支承,8,1,0,0 结点支承,9,1,0,0 结点支承,10,1,0,0 结点支承,11,1,0,0 结点支承,12,1,0,0 结点支承,13,1,0,0 结点,20,-0.851,0 结点,19,13.442,0 单元,20,18,1,1,1,1